Panasonic SV-SD100VEB / SV-SD100VEG / SV-SD100VGC / SV-SD100VGK / SV-SD100VGN / SV-SD100VPP Service Manual ▷ View online
7 Precautions When
Executing The Main PCB
Replacement Service
Replacement Service
This mode is used to check unit operation and the condition of
the PCB, and to verify that record/playback operations are
occurring normally.
Always set the audio player to the service mode when replacing
the PCB or IC. The service mode is also used for initializing and
writing setting data.
the PCB, and to verify that record/playback operations are
occurring normally.
Always set the audio player to the service mode when replacing
the PCB or IC. The service mode is also used for initializing and
writing setting data.
8.1. Before Entering The Service
Mode
Preparations
The following items are required in order to perform an
operation check
· Rechargeable battery (accessory item) (must be fully
operation check
· Rechargeable battery (accessory item) (must be fully
charged)
· One SD card (service mode card)
· One SD card with 8MB space available (for recording
· One SD card with 8MB space available (for recording
check)
· Accessory USB cable
· Personal computer with accessory SD-Jukebox Ver.5.0
· Personal computer with accessory SD-Jukebox Ver.5.0
installed
8.1.1. Preparing The Service Mode SD-
Card
Preparation procedure for SD card
1. Connect the audio player to the personal computer
where the accessory SD-Jukebox Ver.5.0 software is
installed.
installed.
2. Insert the SD-card.
3. Use SD-Jukebox Ver.5.0 to write a music file to the SD-
3. Use SD-Jukebox Ver.5.0 to write a music file to the SD-
card.
4. End SD-Jukebox Ver.5.0 operation.
5. Download the necessary files (SD100TST.SDA and
5. Download the necessary files (SD100TST.SDA and
FLASH_WR.BIN) from TSN-WEB (Support Information
From NWBG-PAVC).
From NWBG-PAVC).
6. Copy the files (SD100TST.SDA and FLASH_WR.BIN)
into
the
SD-card´s root
directory.(The
personal
computer recognizes the audio player as a removable
disk.)
disk.)
7. Disconnect the audio player from the personal
computer.
8. Perform a voice recording to the SD-card at the audio
player.
Note:
If you may not be able to complete a downloding from
the TSN-WEB page, Please order a jig SD card
(RFKZ0294) or obtain the files (SD100TST.SDA and
FLASH_WR.BIN) through your local Panasonic Service
Organization.
the TSN-WEB page, Please order a jig SD card
(RFKZ0294) or obtain the files (SD100TST.SDA and
FLASH_WR.BIN) through your local Panasonic Service
Organization.
The supplied device key loaded PCB (REP3902A-M) does not
contain the regional default settings file.
That file must be written to the audio player by the procedure
shown below.
1. Execute the "8.9. SERVICE 7: Default Settings Writing"
contain the regional default settings file.
That file must be written to the audio player by the procedure
shown below.
1. Execute the "8.9. SERVICE 7: Default Settings Writing"
procedure".
Preparation procedure for jig SD card
1. Connect the audio player to the personal computer
where the accessory SD-Jukebox Ver.5.0 software is
installed.
installed.
2. Insert the jig SD-card (RFKZ0294).
3. Open the jig SD-card from the personal computer. (The
3. Open the jig SD-card from the personal computer. (The
personal computer recognizes the audio player as a
removable disk.)
· The SD-card´s root directory contains the
removable disk.)
· The SD-card´s root directory contains the
SD100TST.SDA
service
mode
file,
and
FLASH_WR_XXXXXXXX.BIN
*
regional
default
settings file.
* "XXXXXXXX" denotes the region and model
names.
* "XXXXXXXX" denotes the region and model
names.
4. Change the file name of the desired region´s
FLASH_WR_XXXXXXXX.BIN to "FLASH_WR.BIN".
5. Use SD-Jukebox Ver.5.0 to write a music file to the SD-
card.
6. End SD-Jukebox Ver.5.0 operation.
7. Disconnect the audio player from the personal
7. Disconnect the audio player from the personal
computer.
8. Perform a voice recording to the SD-card at the audio
player.
* Use the service mode´s "audio playback check" and
"voice playback check" functions for audio files and voice
files.
Because the time required for this operation is determined
by the length of the file, the file should be as short as
possible.
"voice playback check" functions for audio files and voice
files.
Because the time required for this operation is determined
by the length of the file, the file should be as short as
possible.
8.1.2. Preparing The Recording Check
SD-Card
1. Connect the audio player to the personal computer where
the accessory SD-Jukebox Ver.5.0 software is installed.
2. Format an 8MB SD-card at SD-Jukebox Ver.5.0.
3. Disconnect the audio player from the personal computer.
* This card will be used for the "voice recording check"
and "FM recording check" functions. The time required for
this operation depends on the SD-card capacity.
When using an 8MB SD-card, one "SD-card formatting, full
recording and playback" cycle takes approximately 1 hour.
3. Disconnect the audio player from the personal computer.
* This card will be used for the "voice recording check"
and "FM recording check" functions. The time required for
this operation depends on the SD-card capacity.
When using an 8MB SD-card, one "SD-card formatting, full
recording and playback" cycle takes approximately 1 hour.
8 Service Mode
9
SV-SD100VEB / SV-SD100VEG / SV-SD100VGC / SV-SD100VGK / SV-SD100VGN / SV-SD100VPP
8.2. Entering The Service Mode
1. Place a fully charged battery in the audio player and turn
the power ON.
2. Select the audio mode.
3. Insert the service mode SD-card in the audio player.
3. Insert the service mode SD-card in the audio player.
· A playback operation begins.
4. Press the [STOP] button to stop the playback.
5. Press the [MODE] button one time to display the mode
5. Press the [MODE] button one time to display the mode
selection screen (Fig.S1).
6. Use the [FWD-Skip] and [REW-Skip] buttons to select the
desired SERVICE item, then press the [PLAY/STOP] button
to display the service mode menu (Fig.S2).
to display the service mode menu (Fig.S2).
7. At the service mode menu, use the [FWD-Skip] and [REW-
Skip] buttons to select the desired menu item, then press
the [PLAY/STOP] button to execute that menu.
the [PLAY/STOP] button to execute that menu.
Note:
Menus other than SERVICE 1 cannot be executed in a
continuous manner.
continuous manner.
Fig.S1
Fig.S2
8.2.1. Service Mode Function & Canceling The Service Mode
Menu Item
Service Mode
Description
Operation After
Menu Selection
Buttons Used
Canceling The
Service Mode
Service Mode Function
SERVICE 1
Switches the EL
display mode.
display mode.
Returns to standard
screen
screen
[FWD-Skip],
[REW-Skip],
[PLAY/STOP]
(menu operation
only)
[REW-Skip],
[PLAY/STOP]
(menu operation
only)
Turn power OFF, or
switch back to EL
display mode.
switch back to EL
display mode.
Because the display content must be checked
during service mode execution, the EL display is
always ON at this menu.
during service mode execution, the EL display is
always ON at this menu.
SERVICE 2
Device
key
serial
number
display.
Service
mode
is
executed.
None
Turn power OFF.
Verifies that the device key is written without error to
the main PCB´s IC4 (Flash ROM).
the main PCB´s IC4 (Flash ROM).
SERVICE 3
Control
button
operation
checks
checks
and
remaining
battery capacity
display check
battery capacity
display check
Service
mode
is
executed.
[FWD-Skip],
[REW-Skip],
[MODE], [VOL+],
[VOL-] (AD value
measurement)
[REW-Skip],
[MODE], [VOL+],
[VOL-] (AD value
measurement)
Turn power OFF.
Displays the rechargeable battery voltage, and the
KEY
KEY
IN
voltage´s
AD
conversion
values
(hexadecimal) at the [FWD-Skip], [REW-Skip],
[MODE], [VOL+], [VOL-] key operations.
The AD conversion value is used for button
operation checks and for the remaining battery
capacity display.
[MODE], [VOL+], [VOL-] key operations.
The AD conversion value is used for button
operation checks and for the remaining battery
capacity display.
SERVICE 4
Model & region
display
display
Service
mode
is
executed.
None
Turn power OFF.
Displays the model and region information. This
content cannot be changed.
content cannot be changed.
SERVICE 5
Initializes
settings
settings
(all
settings)
Service
mode
is
executed.
[FWD-Skip],
[REW-Skip],
[PLAY/STOP]
(menu operation
only)
[REW-Skip],
[PLAY/STOP]
(menu operation
only)
Turn power OFF
(power
(power
is
automatically
turned OFF when
processing ends).
turned OFF when
processing ends).
Initializes model & region settings, and initializes
resume
resume
information
and
the
tuner´s
preset
frequency.
* This differs from the standard mode´s setting menu
initialization in that the tuner´s preset is also
initialized.
* This differs from the standard mode´s setting menu
initialization in that the tuner´s preset is also
initialized.
SERVICE 6
Reads out the
settings
information.
settings
information.
Service
mode
is
executed.
None
Turn power OFF
(power
(power
is
automatically
turned OFF when
processing ends).
turned OFF when
processing ends).
Verifies that the settings information is written to IC4
(Flash ROM) without error.
(Flash ROM) without error.
SERVICE 7
Writes
the
default settings.
Service
mode
is
executed.
None
Turn power OFF
(power
(power
is
automatically
turned OFF when
processing ends).
turned OFF when
processing ends).
Writes the service mode SD-card´s default setting
file (FLASH_WR.BIN) content to IC4 (Flash
ROM).The model & region settings are written as a
set.
file (FLASH_WR.BIN) content to IC4 (Flash
ROM).The model & region settings are written as a
set.
SERVICE 8
Card
recognition
check
recognition
check
Service
mode
is
executed.
None
Open the battery
cover.
cover.
Verifies that the SD-card (where audio file is saved)
can be recognized.
can be recognized.
SERVICE 9
Checks
the
audio playback
operation.
operation.
Service
mode
is
executed.
None
Open the battery
cover.
cover.
Performs repeat playback and checks for audio
playback errors.
playback errors.
10
SV-SD100VEB / SV-SD100VEG / SV-SD100VGC / SV-SD100VGK / SV-SD100VGN / SV-SD100VPP
8.3. SERVICE 1: EL Display Mode
Switching
Because the display content must be checked during service
mode execution, the EL display is always ON at this menu.
1. Execute the SERVICE 1 menu as described in section 8.2
mode execution, the EL display is always ON at this menu.
1. Execute the SERVICE 1 menu as described in section 8.2
(Entering The Service Mode), and display the EL display
mode switching screen (Fig.S3).
mode switching screen (Fig.S3).
2. Use the [FWD-Skip] and [REW-Skip] buttons to select
"ON", and then press the [PLAY/STOP] button to execute
display mode switching.
display mode switching.
Note:
Another SERVICE mode should be executed within 15
seconds after switching is performed. If the auto power OFF
function is activated, the system returns to the "display
ON/OFF control enabled" mode.
seconds after switching is performed. If the auto power OFF
function is activated, the system returns to the "display
ON/OFF control enabled" mode.
Fig.S3
8.4. SERVICE 2: Device Key Serial
Number. Display
This display is used to verify that the device key is written to the
main PCB´s IC4 (Flash ROM) without error.
If the device key serial number fails to display, there is a
problem with the IC4 (Flash ROM). As the IC4 (Flash ROM)
cannot be replaced independently, replace the main PCB with
a device key loaded PCB (REP3902A-M).
Note: Main PCB replacement should be performed with
reference to section 7 (Precautions When Executing The
Main PCB Replacement Service).
1. Execute the "8.3 SERVICE 1: EL Display Mode Switching"
main PCB´s IC4 (Flash ROM) without error.
If the device key serial number fails to display, there is a
problem with the IC4 (Flash ROM). As the IC4 (Flash ROM)
cannot be replaced independently, replace the main PCB with
a device key loaded PCB (REP3902A-M).
Note: Main PCB replacement should be performed with
reference to section 7 (Precautions When Executing The
Main PCB Replacement Service).
1. Execute the "8.3 SERVICE 1: EL Display Mode Switching"
procedure so that EL is always ON.
2. Execute the SERVICE 2 menu as described in section 8.2
(Entering The Service Mode), in order to display 5 bytes of
the device key serial number. (Fig.S4).
the device key serial number. (Fig.S4).
3. Turn the power OFF to complete the procedure.
Fig.S4
Menu Item
Service Mode
Description
Operation After
Menu Selection
Buttons Used
Canceling The
Service Mode
Service Mode Function
SERVICE 10
Checks
the
voice playback
operation.
operation.
Service
mode
is
executed.
None
Open the battery
cover.
cover.
Performs repeat playback and checks for voice
playback errors.
playback errors.
SERVICE 11
Checks
the
voice recording
operation.
operation.
Service
mode
is
executed.
None
Open the battery
cover.
cover.
Repeats the "SD-card formatting, full recording
(recording until card´s capacity is completely used),
and playback" procedure, and checks for voice
recording errors.
(recording until card´s capacity is completely used),
and playback" procedure, and checks for voice
recording errors.
SERVICE 12
Checks the FM
recording
operation.
recording
operation.
After tuner tuning,
Service
Service
mode
is
executed.
[FWD-Skip],
[REW-Skip],
[PLAY/STOP]
(during
[REW-Skip],
[PLAY/STOP]
(during
tuner
tuning only)
Open the battery
cover.
cover.
Performs "FM radio reception, repeats the "SD-card
formatting, full recording (recording until card´s
capacity is completely used), recording, and
playback" procedure, and checks for FM recording
errors.
formatting, full recording (recording until card´s
capacity is completely used), recording, and
playback" procedure, and checks for FM recording
errors.
SERVICE 13
Performs
a
device check.
Service
mode
is
executed.
None
Open the battery
cover.
cover.
Checks for malfunctions at the main PCB´s IC8 and
IC4, and peripheral circuitry.
IC4, and peripheral circuitry.
* Auto power OFF in operation check modes
Although the audio player is equipped with an auto power OFF function, this function is disabled when executing all operation
check mode menu functions except SERVICE 1.
An automatic power OFF which is unrelated to the auto power OFF function occurs at the completion of SERVICE 5, 6, 7.
check mode menu functions except SERVICE 1.
An automatic power OFF which is unrelated to the auto power OFF function occurs at the completion of SERVICE 5, 6, 7.
11
SV-SD100VEB / SV-SD100VEG / SV-SD100VGC / SV-SD100VGK / SV-SD100VGN / SV-SD100VPP
8.5. SERVICE 3: Control Button
Operation Check & Remaining
Battery Capacity Display
Check
Battery Capacity Display
Check
Displays the rechargeable battery voltage, and the KEY IN
voltage AD conversion values (hexadecimal) at the [FWD-
Skip], [REW-Skip], [MODE], [VOL+], [VOL-] key operations.
The AD conversion value is used for button operation checks
and for the remaining battery capacity display.
1. Execute the "8.3 SERVICE 1: EL Display Mode Switching"
voltage AD conversion values (hexadecimal) at the [FWD-
Skip], [REW-Skip], [MODE], [VOL+], [VOL-] key operations.
The AD conversion value is used for button operation checks
and for the remaining battery capacity display.
1. Execute the "8.3 SERVICE 1: EL Display Mode Switching"
procedure so that EL is always ON.
2. Execute the SERVICE 3 menu as described in section 8.2
(Entering The Service Mode), in order to display the AD
conversion values (hexadecimal) (Fig.S5).
conversion values (hexadecimal) (Fig.S5).
3. Check the BAT´s AD conversion value and the remaining
battery capacity display.
4. Press each of the [FWD-Skip], [REW-Skip], [MODE],
[VOL+], [VOL-] buttons and verify the changes in the KEY´s
AD conversion value.
AD conversion value.
5. Turn the power OFF to complete the procedure.
Fig.S5
8.5.1. AD Conversion Values
8.5.1.1. BAT (Remaining Battery Capacity
AD Value)
The BAT display (hexadecimal) indicates the voltage of the
internal rechargeable battery.
The internal rechargeable battery voltage = 2.9 (V) x [BAT
display content] / 1024.
[Ex] When the BAT value is "1CC" ("460" as decimal value):
Internal rechargeable battery voltage = 2.9 x 460 / 1024 =
1.3027....= 1.303 (V)
internal rechargeable battery.
The internal rechargeable battery voltage = 2.9 (V) x [BAT
display content] / 1024.
[Ex] When the BAT value is "1CC" ("460" as decimal value):
Internal rechargeable battery voltage = 2.9 x 460 / 1024 =
1.3027....= 1.303 (V)
Remaining Battery Voltage
Display
AD Conversion Value
3 battery marks
1C3 < Batt
2 battery marks
1B3 < Batt < or = 1C3
1 battery mark
19B < Batt < or = 1B3
Blinking battery mark
161 < Batt < or = 19B
Low battery voltage
Batt < or = 161
8.5.1.2. KEY (Control Button´s AD Value)
Displays the AD value judgment for the button operation.
Button Operation
AD Conversion Value
MODE
000 ~ 0CA
F-SKIP
151 ~ 1CE
R-SKIP
1CF ~ 259
Vol+
25A ~ 2CB
Vol-
2CC ~ 34E
If the AD conversion value displayed at the button operation is
outside the range shown in the table, this may indicate a
hardware malfunction.
outside the range shown in the table, this may indicate a
hardware malfunction.
8.6. SERVICE 4: Model & Region
Display
Displays the model and region information. This content cannot
be changed.
1. Execute the "8.3 SERVICE 1: EL Display Mode Switching"
be changed.
1. Execute the "8.3 SERVICE 1: EL Display Mode Switching"
procedure so that EL is always ON.
2. Execute the SERVICE 4 menu as described in section 8.2
(Entering The Service Mode), in order to display the model
and region information (Fig.S6).
and region information (Fig.S6).
3. Turn the power OFF to complete the procedure.
Fig.S6
12
SV-SD100VEB / SV-SD100VEG / SV-SD100VGC / SV-SD100VGK / SV-SD100VGN / SV-SD100VPP
Click on the first or last page to see other SV-SD100VEB / SV-SD100VEG / SV-SD100VGC / SV-SD100VGK / SV-SD100VGN / SV-SD100VPP service manuals if exist.