Panasonic SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN Service Manual ▷ View online
4 Component Part Name
Input switch for adjusting left and right input
individually (L/R SPLIT)
Input switch (CH1-CH4)
CD/LINE DIGITAL: Line or CD input, Digital input
LINE: Line input
PHONO 1-3: Turntable phono input
Input control knob (CH1-CH4)
Input level control knob (TRIM)
High-tone input control knob (HIGH)
Mid-tone input control knob (MID)
Low-tone input control knob (LOW)
Channel effect (CH1-CH4) switch (EFFECT)
Power indicator lamp (POWER)
Output level meter (OUTPUT LEVEL)
Play mode lamp (PLAY MODE)
Master output control knob (MASTER)
Master level volume control knob (MASTER LEVEL)
Master balance control knob (MASTER BALANCE)
Output separation ON, OFF switch (SEPARATE OUT)
Monitor control knob (MONITOR)
Monitor level volume control knob (LEVEL)
Monitor mixing control knob (MIXING)
Monitor mode switch (MODE)
Monitor select button-display lamp (CUE)
CH1-CH4: CH1-CH4 monitor selector
EFFECT: Effector monitor selector
Channel fader (CH1 - CH4)
Cross fader (CROSS FADER)
Cross fader Assign A, B switch
(C. FADER ASSIGN)
Effector output switch (PRE/POST)
Input-output effect control knob (EFFECT)
Output effect control knob (SEND)
Input effect control knob (RETURN)
Microphone input control knob (MIC)
Microphone level volume control knob (MIC LEVEL)
High-tone microphone control knob (HIGH)
Low-tone microphone control knob (LOW)
Control panel
6
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
Cross fader curve control switch
(C.FADER CURVE)
Curve switch (CURVE)
Cross fader operation switch (CROSS FADER)
Fader operation switch (CH1-CH4 FADER)
Headphone terminal (PHONES)
Fader start (ON, OFF) switch (FADER START)
Front panel
Rear panel
Power button (POWER
OFF
ON)
Turntable earth terminal (PHONO EARTH)
Input terminal (CH1-CH4)
CD/LINE: CD or line terminal
LINE: Line terminal
PHONO 1-3: Turntable phono terminal
Microphone input terminal (MIC1, MIC2)
Effector input-output terminal
(EFFECT RETURN, EFFECT SEND)
Player control (CH1, CH4) terminal
(PLAYER CONTROL)
Digital output terminal (DIGITAL OUT)
Digital input (CH1, CH4) terminal (DIGITAL IN)
Output terminal
Master out 1, 2 terminal (MASTER OUT)
Monitor out terminal (MONITOR OUT)
Rec terminal (REC OUT)
Power input terminal (AC IN
)
7
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
5 Fader Replacement Instructions
DJ Mixer
Fader Replacement Instructions
Fader Replacement Instructions
First, remove the AC power supply cord (AC mains
lead) and follow the steps below to replace with a
new fader.
lead) and follow the steps below to replace with a
new fader.
1
Remove all five channel fader,
cross fader knobs, and the re-
placement panel
cross fader knobs, and the re-
placement panel
Remove the four plate screws on the replace-
ment panel.
ment panel.
Replacement panel
2
Remove the channel fader or
cross fader to be replaced
cross fader to be replaced
Do not let the screws fall inside the
unit.
unit.
-1 Remove the two fader fastening
screws
-2 Remove the fader
Channel fader
Turn on an angle and lift to remove.
Cross fader
Turn on an angle and lift to remove.
Turn on an angle and lift to remove.
Cross fader
Turn on an angle and lift to remove.
-3 Remove the fader cable while hold-
ing the 3 pin connector
3 pin connector
-4
Cross fader
Remove the two fastening screws, the
optical device unit, and then the cross
fader.
optical device unit, and then the cross
fader.
• Move the lever toward the center and
remove.
• Do not change the shape of the optical
device unit or the 4 pin terminal.
Lever
4 pin terminal
4 pin terminal
3
Attach the new channel fader or
cross fader
cross fader
Attach by performing the opposite of the re-
move step.
move step.
4
Attach the replacement panel and
knobs
knobs
8
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
· This section describes procedures for checking the
operation of the major printed circuit boards and replacing
the main components.
the main components.
· For reassembly after operation checks or replacement,
reverse the respective procedures. Special reassembly
procedures are described only when required.
procedures are described only when required.
6.1. Checking for the output
P.C.B., monitor P.C.B., sub
P.C.B., headphones P.C.B. and
front sw P.C.B.
P.C.B., headphones P.C.B. and
front sw P.C.B.
6 Operation Checks and Component Replacement
Procedures
9
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
Click on the first or last page to see other SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN service manuals if exist.