Panasonic SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN Service Manual ▷ View online
1 Safety Precaution
(This “Safety Precaution” is applied only in U.S.A.)
1. Before servicing, unplug the power cord to prevent an electric shock.
2. When replacing parts, use only manufacturer’s recommended components for safety.
3. Check the condition of the power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, be sure to make the following insulation resistance test to prevent the
customer from being exposed to a shock hazard.
nInsulation Resistance Test
1. Unplug the power cord and short the two prongs of the plug with a jumper wire.
2. Turn on the power switch.
3. Measure the resistance value with ohmmeter between the jumper AC plug and each exposed metal cabinet part, such as screw
heads, control shafts, handle brackets, etc. Equipment with antenna terminals should read between 3M
Ω and 5.2MΩ to
allexposedparts. (Fig. A) Equipment without antenna terminals should read approximately infinity to all exposed parts. (Fig. B)
*Note: Some exposed partsmay beisolated from the chassis by design. These will read infinity.
*Note: Some exposed partsmay beisolated from the chassis by design. These will read infinity.
(Fig. A)
(Fig. B)
4. If the measurement is outside the specified limits, there is a possibility of a shock hazard. The equipment should be repaired
and rechecked before it is returned to the customer.
3
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
2 Caution for AC Mains Lead
4
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
· AC power supply cord....................................................1pc.
−
−
−
− For U.S.A. and Canada. (K2CB2CB00006)
−
−
−
− For the United Kingdom. (RJA0053-3X)
−
−
−
− For Australia and New Zealand. (K2CJ2DA00008)
−
−
−
− For others (RJA0019-2X)
Note:
The included AC power supply cord is for use with this unit
only.
Do not use it with other equipment.
The included AC power supply cord is for use with this unit
only.
Do not use it with other equipment.
3 Accessories
5
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
4 Component Part Name
Input switch for adjusting left and right input
individually (L/R SPLIT)
Input switch (CH1-CH4)
CD/LINE DIGITAL: Line or CD input, Digital input
LINE: Line input
PHONO 1-3: Turntable phono input
Input control knob (CH1-CH4)
Input level control knob (TRIM)
High-tone input control knob (HIGH)
Mid-tone input control knob (MID)
Low-tone input control knob (LOW)
Channel effect (CH1-CH4) switch (EFFECT)
Power indicator lamp (POWER)
Output level meter (OUTPUT LEVEL)
Play mode lamp (PLAY MODE)
Master output control knob (MASTER)
Master level volume control knob (MASTER LEVEL)
Master balance control knob (MASTER BALANCE)
Output separation ON, OFF switch (SEPARATE OUT)
Monitor control knob (MONITOR)
Monitor level volume control knob (LEVEL)
Monitor mixing control knob (MIXING)
Monitor mode switch (MODE)
Monitor select button-display lamp (CUE)
CH1-CH4: CH1-CH4 monitor selector
EFFECT: Effector monitor selector
Channel fader (CH1 - CH4)
Cross fader (CROSS FADER)
Cross fader Assign A, B switch
(C. FADER ASSIGN)
Effector output switch (PRE/POST)
Input-output effect control knob (EFFECT)
Output effect control knob (SEND)
Input effect control knob (RETURN)
Microphone input control knob (MIC)
Microphone level volume control knob (MIC LEVEL)
High-tone microphone control knob (HIGH)
Low-tone microphone control knob (LOW)
Control panel
6
SH-MZ1200PP / SH-MZ1200EB / SH-MZ1200EG / SH-MZ1200EP / SH-MZ1200GN
