DOWNLOAD Panasonic SH-FX67EE / SE-FX67EE / SH-FX67TEE Service Manual ↓ Size: 808.83 KB | Pages: 12 in PDF or view online for FREE

Model
SH-FX67EE SE-FX67EE SH-FX67TEE
Pages
12
Size
808.83 KB
Type
PDF
Document
Simplified Service Manual
Brand
Device
Audio / WIRELESS SYSTEM AND DIGITAL TRANSMITTER
File
sh-fx67ee-se-fx67ee-sh-fx67tee.pdf
Date

Panasonic SH-FX67EE / SE-FX67EE / SH-FX67TEE Simplified Service Manual ▷ View online

I AMPLIFIER SECTION
Output power
RMS output power
Surround Ch
125 W per channel (3
Ω), 1 kHz, 10
% THD
Total RMS power
250 W
DIN output power
Surround Ch
70 W per channel (3
Ω), 1 kHz, 1 %
THD
Total DIN power
140 W
I GENERAL
Power supply
AC 230 V, 50Hz
Power consumption
SH-FX67T
1.5 W
SE-FX67
43 W
Dimensions (W x H x D)
SH-FX67T
65 mm x 52 mm x 8.6 mm
SE-FX67
165 mm x 90 mm x 164 mm
Mass
SH-FX67EE
SE-FX67EE
SH-FX67TEE
Colour
(K)..........Black Type
SH-FX67T
0.02 kg
SE-FX67
0.720 kg
Wireless module
Frequency range
2.400 to 2.4835 GHz
Number of channels
3
Operating temperature range
0 °C to +40 °C
Operating humidity range
20 % to 80 % RH (no condensation)
Power consumption in off mode
approx. 0.3 W
Notes:
 1. 
Specifications are subject to change without notice.
Mass and dimensions are approximate
 2. 
Total harmonic distortion is measured by a digital spectrum
analyzer
Power supply:
This model uses Switching Mode Power Supply (SMPS) Module for
powering the receiver unit. It is replaceable as an assembly unit.
TX / RX Module P.C.B.:
It is replaceable as a TX / RX kit assembly unit.
Wireless System and Digital Transmitter
Please use this manual together with the service manual for Model No. [SH-FX67E-K, SE-FX67E-K, SH-
FX67TE-K, Order No. MD0801018CE].
Specification
ORDER NO. MD0802011AE
 1 
Note 
3
 2 
Safety Precautions 
4
 3 
Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 
6
 4 
Handling the Lead-free Solder 
7
 5 
Exploded Views 
9
 6 
Service Hint 
11
 7 
Replacement Parts List 
12
CONTENTS
 Page 
Page
2
SH-FX67EE / SE-FX67EE / SH-FX67TEE
1 Note
This service manual does not contain the following information:
 • Using of Digital Receiver Unit
 • Self-Diagnosis and Special Mode Setting
 • Assembling and Disassembling
 • Service Positions
 • Voltage Measurement
 • Wiring Connection Diagram
 • Block Diagram
 • Notes of Schematic Diagram
 • Schematic Diagram
 • Printed Circuit Board Diagram
 • Illustration of IC’s, Transistors and Diodes
Please refer to the orginal service manual of SH-FX67E-K, SE-FX67E-K, SH-FX67TE-K (Order No. MD0801018CE) for the above
mention contents.
3
SH-FX67EE / SE-FX67EE / SH-FX67TEE
2 Safety Precautions
2.1. GENERAL GUIDELINES
 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
 3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
2.1.1. LEAKAGE CURRENT COLD CHECK
 1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1M
Ω and 5.2Ω.
When the exposed metal does not have a return path to the chassis, the reading must be
.
2.1.2. LEAKAGE CURRENT HOT CHECK (See Figure 1.)
 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
 2. Connect a 1.5k
Ω, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
 3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
 4. Check each exposed metallic part, and measure the voltage at each point.
 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
 6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may
be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the limits
specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to
the customer.
Figure. 1
4
SH-FX67EE / SE-FX67EE / SH-FX67TEE
Page of 12
Display

Panasonic SH-FX67EE / SE-FX67EE / SH-FX67TEE Simplified Service Manual ▷ Download

  • DOWNLOAD Panasonic SH-FX67EE / SE-FX67EE / SH-FX67TEE Service Manual ↓ Size: 808.83 KB | Pages: 12 in PDF or view online for FREE
  • Here you can View online or download the Simplified Service Manual for the Panasonic SH-FX67EE / SE-FX67EE / SH-FX67TEE in PDF for free, which will help you to disassemble, recover, fix and repair Panasonic SH-FX67EE / SE-FX67EE / SH-FX67TEE Audio. Information contained in Panasonic SH-FX67EE / SE-FX67EE / SH-FX67TEE Simplified Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.