Panasonic SB-PF660GC Service Manual ▷ View online
Type
3 way, 3 speaker system (Bass reflex)
Speaker unit(s)
Impedance 3
Ω
1. Super tweeter
Piezo type
2. Tweeter
6 cm cone type
3. Woofer
16 cm cone type
Input power (IEC)
115 W (Max)
Output sound pressure
82 dB/W (1.0 m)
Cross over frequency
4.16 Hz, 10 kHz
Frequency range
30 Hz to 280 kHz (-16 dB)
SB-PF660GC
Colour
(K)... Black Type
38 Hz to 21 kHz (-10 dB)
Dimensions (W x H x D)
220mm x 330mm x 182 mm
Mass
2.6 kg
Notes :
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
analyzer.
Speaker System
Specification
ORDER NO. MD0707005CE
1 System Combination
1.1. System Breakdown
Note :
The tables below show the breakdown for speaker combinations used in main unit systems.
System SC-VK660EE-K
Music center
Music center
SA-VK660EE-K
Front speaker
SB-PF660GC-K
Subwoofer
SB-WVK660GC-K
System SC-VK660GC-K
Music center
Music center
SA-VK660GC-K
Front speaker
SB-PF660GC-K
Subwoofer
SB-WVK660GC-K
System SC-VK660GCSK
Music center
Music center
SA-VK660GCSK
Front speaker
SB-PF660GC-K
Subwoofer
SB-WVK660GC-K
System SC-VK660GCTK
Music center
Music center
SA-VK660GCTK
Front speaker
SB-PF660GC-K
Subwoofer
SB-WVK660GC-K
System SC-VK660GN-K
Music center
Music center
SA-VK660GN-K
Front speaker
SB-PF660GC-K
Subwoofer
SB-WVK660GC-K
System SC-VK660GS-K
Music center
Music center
SA-VK660GS-K
Front speaker
SB-PF660GC-K
Subwoofer
SB-WVK660GC-K
2
SB-PF660GC
2 Assembling and Disassembling
“ATTENTION SERVICER”
Some chassis components may have sharp edges. Be careful when disassembling and servicing.
1. This section describes procedures for checking the operation and replacing the main components.
2. For reassembly after operation checks or replacement, reverse the respective procedures.
Special reassembly procedures are described only when required.
3. Select items from the following index when checks or replacement are required.
4. Refer to the Parts No. on the page of “Parts Location and Replacement Parts List” (Section 5), if necessary.
Below is the list of disassembly sections
•
Disassembly of Rear cabinet assembly
•
Disassembly of Tweeter (SP1)
•
Disassembly of Woofer (SP2)
2.1. Disassembly flow chart
The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the
servicing.
servicing.
To assemble the unit, reverse the steps shown in the chart as below.
3
SB-PF660GC
2.2. Disassembly of Rear cabinet
assembly
Step 1: Remove 4 screws.
Step 2: Insert flathead screwdriver into the grooves to push the
front panel as arrow shown.
front panel as arrow shown.
Step 3: Detach the front panel as arrow shown.
Step 4: Remove the glue from wire assembly.
Step 5: Remove ceramic buzzer as arrow shown.
4
SB-PF660GC