Panasonic SB-HW560E Service Manual ▷ View online
Type
1 way, 1 speaker system (Kelton type)
Speaker unit(s)
Impedance 6
!
1. Woofer
16 cm Cone type
2. Passive Radiator
25 cm
Input power (IEC)
250 W (Max)
Output sound pressure
78 dB/W (1.0 m)
Frequency range
35 Hz to 200 Hz (-16 dB)
40 Hz to 198 Hz (-10 dB)
SB-HW560E
Colour
(K) .... Black Type (For PT560E/EB/EG-K,E/EG-S,
(K) .... Black Type (For PT560E/EB/EG-K,E/EG-S,
PT560EE-K/S,GN-K/GCPK)
(K1) .... Black Type (For PT660/760/960P, BT100P,
PT760PL, PT760/960PX)
(K2) .... Black Type (For PT954P)
(K3) .... Black Type (For BT100EB/EG/EE,
(K3) .... Black Type (For BT100EB/EG/EE,
BT100GC/GCS/GCP/GN)
(K4) .... Black Type (For PT565GC/GS/GCT/GCS,
PT565GCSX)
Dimensions (W x H x D)
181 mm x 361 mm x 315 mm
Mass
4.7 kg
Notes :
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
Speaker System
Specification
ORDER NO. MD0801009CE
A6
1 Assembling and Disassembling
“ATTENTION SERVICER”
Some chassis components may have sharp edges. Be careful when disassembling and servicing.
1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main
components.
2. For reassembly after operation checks or replacement, reverse the respective procedures.
Special reassembly procedures are described only when required.
3. Select items from the following index when checks or replacement are required.
4. Refer to the Parts No. on the page of “Parts Location and Replacement Parts List” (Section 5), if necessary.
4. Refer to the Parts No. on the page of “Parts Location and Replacement Parts List” (Section 5), if necessary.
Below is the list of disassembly sections
# Disassembly of Side panel unit
# Disassembly of Passive radiator
# Disassembly of Woofer unit (SP1)
# Disassembly of Passive radiator
# Disassembly of Woofer unit (SP1)
2
SB-HW560E
Step 1: Peel off the screw covers by using the pen knife.
Note: Place it in original location during assembling.
Step 2: Remove 4 screws.
Step 3: Insert the flathead screwdriver into the grooves of the
side panel unit.
Step 4: Lift up the side panel unit slightly.
side panel unit.
Step 4: Lift up the side panel unit slightly.
1.1. Disassembly of Side panel unit
3
SB-HW560E
Step 5: Insert two flathead screwdrives at the sides of the boss
and apply force to gently push out the side panel unit as picture
shown.
Step 6: Follow step 5 for the other bosses in sequence to push
out the side panel unit.
and apply force to gently push out the side panel unit as picture
shown.
Step 6: Follow step 5 for the other bosses in sequence to push
out the side panel unit.
Caution:
Do not exert too much force as it may damage the side panel
unit.
Do not exert too much force as it may damage the side panel
unit.
Step 7: Remove side panel unit as arrow shown.
1.2. Disassembly of Passive
radiator
Follow (Step 1) to (Step 7) in item 1.1.
Step 1: Remove 8 screws.
Step 2: Insert the flathead screwdriver between passive
radiator and speaker cabinet assembly.
Step 3: Gently lift up and remove passive radiator as arrow
shown.
radiator and speaker cabinet assembly.
Step 3: Gently lift up and remove passive radiator as arrow
shown.
Caution:
Ensure the flathead screwdriver is above the cloth to avoid
damage on speaker cabinet assembly.
Ensure the flathead screwdriver is above the cloth to avoid
damage on speaker cabinet assembly.
4
SB-HW560E