Panasonic SB-HF167GS / SB-HC270P / SB-HS270P / SB-HW370EG / SB-XH155EG Service Manual ▷ View online
2
1 Service Navigation
1.1.
System Information (SB-XH155EG-K)
Below is the System breakdown:
SB-XH155EG-K is use for the following main models:
SC-XH155EE-K
SC-XH155EP-K
SC-XH155GA-K
SC-XH155GS-K
SC-XH155PH-K
SC-XH155EE-K
SC-XH155EP-K
SC-XH155GA-K
SC-XH155GS-K
SC-XH155PH-K
1.2.
Front Speakers (SB-HF167GS-K)
The illustrations for the Speakers will be described in this manual.
• Disassembly and Assembly Instructions
• Wiring Connection Diagram
• Exploded View
• Replacement Parts List
• Wiring Connection Diagram
• Exploded View
• Replacement Parts List
1.3.
Subwoofer Speaker (SB-HW370EG-K)
The illustrations for the Speakers will be described in this manual.
• Wiring Connection Diagram
• Exploded View
• Replacement Parts List
• Exploded View
• Replacement Parts List
Speaker System
SB-XH155EG-K
Front Speakers
SB-HF167GS-K
Center Speaker
SB-HC270P-K
Surround Speakers
SB-HS270P-K
Subwoofer Speaker
SB-HW370EG-K
3
2 Specifications
Front Speakers (SB-HF167GS-K)
Type
Type
1 way, 1 speaker system (Bass reflex)
Speaker unit(s)
Impedance 3
Ω
Full range
6.5 cm Cone Type
Output sound pressure
78 dB/W (1 m)
Frequency range
105 Hz to 25 kHz (-16 dB),
130 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
291.2 mm x 1185 mm x 291.2 mm
Mass [Weight]
2.35 kg
Full assembly with stand base
Dimensions (W x H x D) max
Dimensions (W x H x D) max
255 mm x 1020 mm x 255 mm
Dimensions (W x H x D) min
255 mm x 550 mm x 255 mm
Mass [Weight]
2.3 kg
Center Speaker (SB-HC270P-K)
Type
Type
1 way, 1 speaker system (Bass reflex)
Speaker unit(s)
Impedance 3
Ω
Full range
6.5 cm Cone type
Output sound pressure
79 dB/W (1 m)
Frequency range
90 Hz to 25 kHz (-16 dB),
115 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
145 mm x 81 mm x 70.5 mm
Mass [Weight]
0.52 kg
Surround Speakers (SB-HS270P-K)
Type
Type
1 way, 1 speaker system (Bass reflex)
Speaker unit(s)
Impedance 3
Ω
Full range
6.5 cm Cone type
Output sound pressure
78 dB/W (1 m)
Frequency range
105 Hz to 25 kHz (-16 dB),
130 Hz to 22 kHz (-10 dB)
Dimensions (W x H x D)
80 mm x 117 mm x 70.5 mm
Mass [Weight]
0.35 kg
Subwoofer (SB-HW370EG-K)
Type
Type
1 way, 1 speaker system (Bass reflex)
Speaker unit(s)
Impedance 3
Ω
Woofer
16 cm Cone type
Output sound pressure
78 dB/W (1 m)
Frequency range
30 Hz to 220 Hz (-16 dB),
35 Hz to 180 Hz (-10 dB)
Dimensions (W x H x D)
180 mm x 408 mm x 300 mm
Mass [Weight]
4.3 kg
Notes:
1. Specifications are subject to change without notice.
1. Specifications are subject to change without notice.
4
3 Disassembly and Assembly Instructions
“ATTENTION SERVICER”
Some chassis components may have sharp edges. Be careful when disassembling and servicing.
1. This section describes procedures for checking the operation and replacing the main components.
2. For reassembly after operation checks or replacement, reverse the respective procedures.
2. For reassembly after operation checks or replacement, reverse the respective procedures.
Special reassembly procedures are described only when required.
3. Select items from the following index when checks or replacement are required.
4. Refer to the Parts No. on the page of “Exploded View and Replacement Parts List” (Section 5), if necessary.
4. Refer to the Parts No. on the page of “Exploded View and Replacement Parts List” (Section 5), if necessary.
Below is the list of disassembly sections
• Front Speakers (SB-HF167GS-K)
Disassembly of Upper Box Assembly
Disassembly of Upper Rear Cabinet Assembly
Disassembly of Tweeter Speaker (SP1)
Disassembly of Lower Box Assembly
Disassembly of Speaker Wire
Disassembly of Base Cover
Disassembly of Upper Rear Cabinet Assembly
Disassembly of Tweeter Speaker (SP1)
Disassembly of Lower Box Assembly
Disassembly of Speaker Wire
Disassembly of Base Cover
5
3.1.
Front Speakers (SB-HF167GS-K)
3.1.1.
Dissassembly of Upper Box
Assembly
Assembly
Step 1: Remove the Bule (+) and Grey (-) wires.
Step 2: Pull out the Speaker Wire from the groove.
Step 2: Pull out the Speaker Wire from the groove.
Step 3: Remove 1 screw from Upper Box Assembly.
Step 4: Detach the Upper Box Assembly.