Panasonic SB-FS1000E / SB-FC1000LE / SB-FC1000RE / SB-HS1000E / SB-WA1000E / SB-TP1000E Service Manual ▷ View online
SB-FC1000L [For front speaker (left)]
SB-FC1000R [For front speaker (right)]
Front speaker section
Type
3 way 4 speaker system Bass-
reflex type
Speaker
Woofer (1 & 2)
8 cm cone type x 2
Tweeter (1)
2.5 cm dome type x 1
Super tweeter
1.2 cm dome type x 1
Impedance
6
Ω
Input power (IEC)
200 W (Max), 100 W (RATED)
Sound pressure level
82.5 dB/W (1.0 m)
Crossover frequency
2.5 kHz, 20 kHz
Frequency range
65 Hz - 100 kHz (at -16 dB)
75 Hz - 90 kHz (at -10 dB)
Center speaker section
Type
3 way 3 speaker system Bass-
reflex type
Speakers
Woofer (3)
8 cm cone type x 1
Midrange
6.5 cm cone type x 1
Tweeter (2)
2.5 cm dome type x 1
Impedance
12
Ω
Input power (IEC)
100 W (Max), 50 W (RATED)
Sound pressure level
80 dB/W (1.0 m)
SB-FS1000E
SB-FC1000LE
SB-FC1000RE
SB-HS1000E
SB-WA1000E
SB-TP1000E
Colour
(K)... Black Type
(K)... Black Type
Crossover frequency
800 Hz, 3 kHz
Frequency range
65 Hz - 50 kHz (at -16 dB)
75 Hz - 40 kHz (at -10 dB)
General
Dimensions (W x H x D)
279 mm x 1298 mm x 279 mm
(with the stand)
175 mm x 802 mm x 102 mm (For
w-mounting)
Mass
Approx. 12.6 kg (with the stand)
Approx. 5.4 kg (For w-mounting)
SB-HS1000E (For surround speakers)
Type
2 way 3 speaker system Bass-
reflex type
Speakers
Woofer (1 & 2)
8 cm cone type x 2
Tweeter
2.5 cm dome type x 1
Impedance
6
Ω
Input power (IEC)
200 W (Max), 100 W (RATED)
Sound pressure level
82.5 dB/W (1.0 m)
Crossover frequency
2.5 kHz
Frequency range
65 Hz - 50 kHz (at -16 dB)
75 Hz - 40 kHz (at -10 dB)
Dimensions (W x H x D)
279 mm x 1298 mm x 279 mm
(with the stand)
Speaker System
Specification
ORDER NO. MD0807010CE
125 mm x 802 mm x 87 mm (For
wall-mounting)
Mass
Approx. 9.3 kg (with the stand)
Approx. 3.7 kg (For wall-mounting)
SB-WA1000E [For Active Subwoofer]
I SPEAKER SECTION
Type
1 way 2 speaker system
Bass-reflex type
Speaker
Woofer (1 & 2)
17 cm cone type x 2
Sound pressure level
83 dB/W (1.0 m)
Frequency range (with amp)
28 Hz - 300 Hz (at -16 dB)
32 Hz - 240 Hz (at -10 dB)
I AMPLIFIER SECTION
Output power
Output power
100 W (6
Ω) x 2 (THD 0.9%)
Input sensitivity / Input Impedance
300 mV/33 k
Ω (RCA jack)
1
Safety Precautions
3
2
Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
6
3
About Lead-Free Solder (PbF)
7
4
Accessories
8
5
Operating Instructions Procedures
9
6
Assembling and Disassembling
14
7
Voltage Measurement and Waveform Chart
39
8
Connection of Speaker wiring
42
Phase switching
NORMAL/REVERSE
Low pass filter
50 Hz - 200 Hz Variable
I GENERAL
Power supply
AC 230 V - 240 V, 50Hz
Power consumption
140 W
Dimensions (W x H x D)
254 mm x 496 mm x 500 mm
Mass
Approx. 22 kg
Power consumption in input
standby condition:
standby condition:
1.5 W
ISpeaker System : SB-TP1000E-K
Front speaker (L) : SB-FC1000LE-K
Front speaker (R) : SB-FC1000RE-K
Surround speaker : SB-HS1000E-K
Active subwoofer : SB-WA1000E-K
Notes :
Specifications are subject to change without notice.
9
Wiring Connection Diagram
43
10 Block Diagram
45
11 Notes Of Schematic Diagram
47
12 Schematic Diagram
49
13 Printed Circuit Board
53
14 Illustration of IC’s, Transistors and Diodes
55
15 Exploded view
57
16 Replacement Parts List
63
CONTENTS
Page
Page
2
SB-FS1000E / SB-FC1000LE / SB-FC1000RE / SB-HS1000E / SB-WA1000E / SB-TP1000E
1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, ensure that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
3. After servicing, check for leakage current checks to prevent from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Using an ohmmeter measure the resistance value, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1M
chassis, the reading should be between 1M
Ω and 5.2Ω.
When the exposed metal does not have a return path to the chassis, the reading must be
.
Figure 1
1.1.2. Leakage Current Hot Check (See Figure 1)
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5k
Ω, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may
be used to make the hot checks, leakage current must not exceed 1/2 milliamp. should the measurement is outside of the limits
specified, there is a possibility of a shock hazard, and the equipment should be repaired and re-checked before it is returned
to the customer.
specified, there is a possibility of a shock hazard, and the equipment should be repaired and re-checked before it is returned
to the customer.
3
SB-FS1000E / SB-FC1000LE / SB-FC1000RE / SB-HS1000E / SB-WA1000E / SB-TP1000E
1.2. Caution for AC Cord
SB-FS1000E / SB-FC1000LE / SB-FC1000RE / SB-HS1000E / SB-WA1000E / SB-TP1000E
4
