Panasonic SA-VK650EE Service Manual ▷ View online
Item
FL Display
Key Operation
Mode Name
Description
Remote Control Key
CD laser drive
current
measurement
current
measurement
CD laser drive current
measurement.
CD laser drive current measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, CD laser
emission is kept on. It is turned off
when POWER key is switched off.
(It is also turned off when POWER
button on the player is switched
off.)
measurement.
CD laser drive current measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, CD laser
emission is kept on. It is turned off
when POWER key is switched off.
(It is also turned off when POWER
button on the player is switched
off.)
The value denotes the current in decimal
notation.
The above example shows the initial current
is 25mA and the measured value is 22mA.
notation.
The above example shows the initial current
is 25mA and the measured value is 22mA.
In STOP (no disc) mode, press STOP
button on the player, and “3” button on the
remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display).
button on the player, and “3” button on the
remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display).
Device Name
Display the device name.
1.
2.
3.
In STOP (no disc) mode, press STOP
button on the player, and “4” button on the
remote control unit. *With pointing of cursor
up and down on display.
Cancelled automatically 5 seconds later.
To exit, press [POWER] button on main
unit or remote control.
button on the player, and “4” button on the
remote control unit. *With pointing of cursor
up and down on display.
Cancelled automatically 5 seconds later.
To exit, press [POWER] button on main
unit or remote control.
Jitter check
Jitter check.
Jitter rate is measured and
displayed.
Measurement is repeatedly done in
the cycle of one second. Read
error counter starts from zero upon
mode setting. When target block
data failed to be read out, the
counter advances by one
increment. When the failure is
caused by minor error, it may be
corrected when retired to enable
successful reading. In this case,
the counter advances by one.
When the error persists even after
retry, the counter may jump by two
or more.
Jitter rate is measured and
displayed.
Measurement is repeatedly done in
the cycle of one second. Read
error counter starts from zero upon
mode setting. When target block
data failed to be read out, the
counter advances by one
increment. When the failure is
caused by minor error, it may be
corrected when retired to enable
successful reading. In this case,
the counter advances by one.
When the error persists even after
retry, the counter may jump by two
or more.
Jitter rate is shown in decimal notation to
one place of decimal.
Focus drive value is shown in hexadecimal
notation.
one place of decimal.
Focus drive value is shown in hexadecimal
notation.
In STOP (no disc) mode, press STOP
button on the player, and “5” button on the
remote control unit.
Press STOP or OPEN button to exit.
Press “FL DISPLAY” button on remote
control unit for next page (FL Display).
button on the player, and “5” button on the
remote control unit.
Press STOP or OPEN button to exit.
Press “FL DISPLAY” button on remote
control unit for next page (FL Display).
Region display
Region display & mode
In STOP (no disc) mode, press STOP
button on the player, and “6” button on the
remote control unit.
Cancelled automatically 5 seconds later.
button on the player, and “6” button on the
remote control unit.
Cancelled automatically 5 seconds later.
Micro- processor
firmware version
display &
EEPROM
checksum display.
firmware version
display &
EEPROM
checksum display.
Micro-processor firmware version
display & EEPROM checksum
display.
display & EEPROM checksum
display.
In STOP (no disc) mode, press STOP
button on the player, and “7” button on the
remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page. (FL Display)
button on the player, and “7” button on the
remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page. (FL Display)
DVD module
firmware version
display
firmware version
display
DVD module firmware version
display is on the FL Display.
display is on the FL Display.
In STOP (no disc) mode, press STOP
button on the player, and “8” button on the
remote control unit.
Cancelled automatically 5 seconds later.
button on the player, and “8” button on the
remote control unit.
Cancelled automatically 5 seconds later.
25
SA-VK650EE
Item
FL Display
Key Operation
Mode Name
Description
Remote Control Key
Initialization
Initialization.
User settings are cancelled and
player is initialized to factory
setting.
User settings are cancelled and
player is initialized to factory
setting.
In STOP (no disc) mode, press STOP
button on the player, and
button on the player, and
button
on the remote control unit.
DVD Module
Reset
Reset
To reset DVD Module.(In
initialisation)
When the FLASH ROM IC or DVD
Module is replaced.
initialisation)
When the FLASH ROM IC or DVD
Module is replaced.
In initialisation, press and hold STOP
button on the player followed by “Enter”
button on the remote control.
Cancelled automatically 5 seconds later.
button on the player followed by “Enter”
button on the remote control.
Cancelled automatically 5 seconds later.
DVD laser drive
current
measurement
current
measurement
DVD laser drive current
measurement.
DVD laser drive current is
measured and the result is
displayed together with the initial
value stored in the EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off.
(It is also turned off when POWER
button on the player is switched
off.)
measurement.
DVD laser drive current is
measured and the result is
displayed together with the initial
value stored in the EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off.
(It is also turned off when POWER
button on the player is switched
off.)
The value denotes the current in decimal
notation.
The above example shows the initial current
is 20mA and the measured value is 20mA.
notation.
The above example shows the initial current
is 20mA and the measured value is 20mA.
In STOP (no disc) mode, press STOP
button on the player, and FUNCTIONS
button on the remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display) on
values of DVD drive current.
button on the player, and FUNCTIONS
button on the remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display) on
values of DVD drive current.
Communic-
ation error display
ation error display
Displays frequency of
communication errors between
system control IC and mechanism
control IC during DVD module.
communication errors between
system control IC and mechanism
control IC during DVD module.
In STOP (no disc) mode, press STOP
button on the player, and “MENU” button
on the remote control unit.
Cancelled automatically 5 seconds later.
button on the player, and “MENU” button
on the remote control unit.
Cancelled automatically 5 seconds later.
Initial setting of
laser drive current
laser drive current
Initial setting of laser drive current.
Initial current value for each of
DVD laser and CD laser is
separately saved in the EEPROM
IC.
Initial current value for each of
DVD laser and CD laser is
separately saved in the EEPROM
IC.
The value denotes the current in decimal
notation. The above example shows the
initial current 20mA and 23mA for DVD laser
and CD laser respectively when the laser is
switched on.
notation. The above example shows the
initial current 20mA and 23mA for DVD laser
and CD laser respectively when the laser is
switched on.
In STOP (no disc) mode, press STOP
button on the player, and PAUSE button on
the remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display) on
values of laser drive current.
button on the player, and PAUSE button on
the remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display) on
values of laser drive current.
ECC error display ECC decode error display.
In STOP (no disc) mode, press STOP
button on the player, and TOP MENU
button on the remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display) on
values of laser drive current.
button on the player, and TOP MENU
button on the remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display) on
values of laser drive current.
Time 1 check
Timer 1 check.
Laser operation time.
Press “FL Display” button for next
page of FL Display (to show CD
laser time).
Laser operation time.
Press “FL Display” button for next
page of FL Display (to show CD
laser time).
Shown to the left is laser time, and to the
right laser time.
Time is shown in 4 digits of decimal notation
in a unit of 10 hours.
“0000” will follow “9999”.
right laser time.
Time is shown in 4 digits of decimal notation
in a unit of 10 hours.
“0000” will follow “9999”.
In STOP (no disc) mode, press STOP
button on the player, and “
button on the player, and “
” button on
the remote control unit.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display) on
values of laser drive current.
Cancelled automatically 5 seconds later.
Press “FL Display” button on remote
control unit for next page (FL Display) on
values of laser drive current.
Timer 1 reset
Timer 1 reset.
Laser operation timer of both DVD
laser and CD laser is reset all at
once.
Laser operation timer of both DVD
laser and CD laser is reset all at
once.
T1_0000/0000 (display1/display2)
Shown to the left is laser time and to the
right is laser time.
Time is shown in 4 digits of decimal notation
in a unit of 10 hours.
It cleared to ‘0000/0000’ upon reset.
Shown to the left is laser time and to the
right is laser time.
Time is shown in 4 digits of decimal notation
in a unit of 10 hours.
It cleared to ‘0000/0000’ upon reset.
While display Timer 1 data, press STOP
button on the player, and “
button on the player, and “
“ button on
the remote control unit.
Cancelled automatically 5 seconds later.
Cancelled automatically 5 seconds later.
Timer 2 check
Timer 2 check.
Spindle motor operation timer.
Press “FL Display” button for next
page of FL Display.
Spindle motor operation timer.
Press “FL Display” button for next
page of FL Display.
Time is shown in 5 digits of decimal notation
in a unit of 10 hours.
“0000” will follow “9999”.
in a unit of 10 hours.
“0000” will follow “9999”.
In STOP (no disc) mode, press STOP
button on the player, and “
button on the player, and “
“ button on
the remote control unit.
Cancelled automatically 5 seconds later.
Cancelled automatically 5 seconds later.
Timer 2 reset
Timer 2 reset.
Spindle motor operation timer.
Spindle motor operation timer.
Time is shown in 5 digits of decimal notation
in a unit of 10 hours.
It cleared to ‘0000’ upon reset.
in a unit of 10 hours.
It cleared to ‘0000’ upon reset.
While display Timer 2 data, press STOP
button on the player, and “
button on the player, and “
“ button on
the remote control unit.
Cancelled automatically 5 seconds later.
Cancelled automatically 5 seconds later.
26
SA-VK650EE
10.2.2. DVD Self-Diagnostic Function Error Code
Error
Code
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
F010
DVD Media disk
A specification value is size from the
PARENTAL
PARENTAL
LOCK
value
of
the
appointed country.
Press [
] on main
unit for next error.
F020
DVD Media disk
There is no TT_SRPT. (RLBN is 0).
Press [
] on main
unit for next error.
F021
DVD Media disk
The number of TT_SRP is 0.
Press [
] on main
unit for next error.
F022
DVD Media disk
A specification value. It is size from the
number of TT_SRP.
number of TT_SRP.
Press [
] on main
unit for next error.
F023
DVD Media disk
VTSN or in agreement with VTS_TTN.
There is no SRP.
There is no SRP.
Press [
] on main
unit for next error.
F024
DVD Media disk
A specification value. It is size from
TT_SRP. PTT_Ns
TT_SRP. PTT_Ns
Press [
] on main
unit for next error.
F030
DVD Media disk
The number of TTU_SRP is 0.
Press [
] on main
unit for next error.
F031
DVD Media disk
A specification value. It is size from the
number of TTU_SRP.
number of TTU_SRP.
Press [
] on main
unit for next error.
F040
DVD Media disk
The number of SRP1 is 0.
Press [
] on main
unit for next error.
F041
DVD Media disk
The number of PGCI_SRP is 0.
Press [
] on main
unit for next error.
F042
DVD Media disk
A specification value. It is size from the
number of PGCI_SRP.
number of PGCI_SRP.
Press [
] on main
unit for next error.
F043
DVD Media disk
It is in agreement with Menu ID. There is
no PGCI_SRP.
no PGCI_SRP.
Press [
] on main
unit for next error.
F050
DVD Media disk
The number of TMAP_SRP is 0.
Press [
] on main
unit for next error.
F051
DVD Media disk
A specification value. It is size from the
number of TMAP_SRP.
number of TMAP_SRP.
Press [
] on main
unit for next error.
F052
DVD Media disk
Specification TMAP_SA is 0.
Press [
] on main
unit for next error.
F053
DVD Media disk
The number of MAP_EN is 0.
Press [
] on main
unit for next error.
F060
DVD Media disk
Although C_POSIT exists, it is in PGC.
There is no PGMAP.
There is no PGMAP.
Press [
] on main
unit for next error.
F061
DVD Media disk
Although C_POSIT exists, it is in PGC.
There is no PGMAP.
There is no PGMAP.
Press [
] on main
unit for next error.
27
SA-VK650EE
Error
Code
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
F062
DVD Media disk
A specification value inside of PGC. It is
size from the number of PGes.
size from the number of PGes.
Press [
] on main
unit for next error.
F063
DVD Media disk
Although C_POSIT exists, it is in PGC.
There is no C_PBIT.
There is no C_PBIT.
Press [
] on main
unit for next error.
F064
DVD Media disk
Although C_POSIT exists, it is in PGC.
The number of PGes is 0.
The number of PGes is 0.
Press [
] on main
unit for next error.
F065
DVD Media disk
Specification A cell number is 0.‘
Press [
] on main
unit for next error.
F066
DVD Media disk
A specification value inside of PGC. It is
size from the number of Cell(s).
size from the number of Cell(s).
Press [
] on main
unit for next error.
F067
DVD Media disk
A blocked cell is present.
Press [
] on main
unit for next error.
F070
DVD Media disk
There is no NV_PACK data.
Press [
] on main
unit for next error.
F080
DVD Media disk
Under reference. There is no Cell
number.
number.
Press [
] on main
unit for next error.
F0E0
DVD Media disk
For [used as a DFD object] a user guide.
A PGC control file < impossible.
A PGC control file < impossible.
Press [
] on main
unit for next error.
F0E1
DVD Media disk
DFD main microcomputer. Compatibility
with a DFD type < download is
impossible.
with a DFD type < download is
impossible.
Press [
] on main
unit for next error.
F0E2
DVD Media disk
DFD download start. PGC reproduction
error.
error.
Press [
] on main
unit for next error.
F0E3
DVD Media disk
Waiting for the completion of DFD
download. PGC reproduction error.
download. PGC reproduction error.
Press [
] on main
unit for next error.
F0E4
DVD Media disk
At the time of DFD download AVDEC.
Press [
] on main
unit for next error.
F0E5
DVD Media disk
It is the farm file lead error at the time of
DFD download.
DFD download.
Press [
] on main
unit for next error.
F0E6
DVD Media disk
DFD alteration check error of the read
firmware.
firmware.
Press [
] on main
unit for next error.
F0F0
DVD Media disk
There is no farm file used as a DFD
object and it is downloading needlessly.
object and it is downloading needlessly.
Press [
] on main
unit for next error.
F0F1
DVD Media disk
The firware which is in agreement with
DFD
DFD
download
conditions
<
unnecessary.
Press [
] on main
unit for next error.
F103
Illegal highlight Position
Big possibility of disc specification
violation during highlight display
violation during highlight display
Press [
] on main
unit for next error.
F4FF
Force initialize failure
(time out)
(time out)
Timeout when force initialization fails
Press [
] on main
unit for next error.
28
SA-VK650EE
Click on the first or last page to see other SA-VK650EE service manuals if exist.