Panasonic SA-BTT790EE / SC-BTT790EEK Service Manual ▷ View online
33
9.1.3.
Special Mode Table 3
Progressive
initialization
initialization
The progressive setting is initialized to
Interlace.
Interlace.
Item
FL display
Key operation
Mode name
Description
Front Key
When the power is on, press &
hold [SKIP REV] on remote control
follow by [POWER] on main unit.
hold [SKIP REV] on remote control
follow by [POWER] on main unit.
Micro-P version
check
check
To check for main & sub firmware version
no., model no. & date of production.
no., model no. & date of production.
FL Display
(1)
T: 021
Timer version
(2)
ROM 06
ROM
(4)
P 3160
Sub Firmware (For EE)
(3)
MV 3160
Main Firmware (For EE)
P 3150
Sub Firmware (For GN)
MV 3150
Main Firmware (For GN)
(5)
Drive Version
D 0104
“HELLO” is displayed 10 seconds.
While the unit is off, press and hold
[OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
[OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the
unit's display.
Repeatedly press
unit's display.
Repeatedly press
[
]
on the
remote control or [POWER] on
the unit until "08 FIN" is
displayed on the unit's display.
Press and hold [OK] on the
remote control or [OPEN/
CLOSE] on the unit for at least
3 seconds.
the unit until "08 FIN" is
displayed on the unit's display.
Press and hold [OK] on the
remote control or [OPEN/
CLOSE] on the unit for at least
3 seconds.
When the power is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds. - "00 RET" is
displayed on the unit's display.
Repeatedly press [R] on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [G] on the
remote control or [OPEN/CLOSE]
on the unit.
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds. - "00 RET" is
displayed on the unit's display.
Repeatedly press [R] on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [G] on the
remote control or [OPEN/CLOSE]
on the unit.
Default setting
The date of Menu, Mode and EEPROM
setting, etc. is set to the default condition in
factory.
setting, etc. is set to the default condition in
factory.
(6)
R1:41:00
For Debug Purpose Only
34
9.1.4.
Special Mode Table 4
Item
FL display
Key operation
Mode name
Description
Front Key
(16)
For Debug Purpose Only
P4:BE:53
(18)
For Debug Purpose Only
P6:AF:10
(17)
For Debug Purpose Only
P5:F6:OD
(13)
P1:2F:CC
For Debug Purpose Only
(12)
P0:FF:90
For Debug Purpose Only
(14)
P2:FF:20
For Debug Purpose Only
(15)
P3:ED:06
For Debug Purpose Only
(10)
DEST: X
DEST: EE (For EE)
DEST: GN (For GN)
Destination Code
DEST: GN (For GN)
Destination Code
(11)
ERR: NONE
Error
(19)
For Debug Purpose Only
P7:CF:30
(7)
POW ON
For Debug Purpose Only
(8)
LADR:14:05
For Debug Purpose Only
(9)
PADR:30:00
For Debug Purpose Only
35
9.1.5.
Special Mode Table 5
Item
FL display
Key operation
Mode name
Description
Front Key
(20)
For Debug Purpose Only
P8:03:EE
(22)
For Debug Purpose Only
P10:CE:20
(21)
For Debug Purpose Only
P9:EB:2D
36
9.2.
Error Codes
Self-Diagnostic Function provides information for error to service personnel by Self-Diagnosis Display when any error has occurred.
U**, H** and F** are stored in my memory and held.
U**, H** and F** are stored in my memory and held.
• You can check latest error code by transmitting [0] [1] of Remote Control in Service Mode.
Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is
ON.
ON.
9.2.1.
Error Code Table 1 (For BD)
Error Code
Diagnosis contents
Description
Monitor Display
Automatic FL display
U30
Remote control code error
Display appears when main unit and remote
controller codes are not matched.
controller codes are not matched.
No display
No display
No display
No display
No display
No display
No display
No display
No display
* is remote controller code of the
main unit.
Display for 5 seconds.
main unit.
Display for 5 seconds.
U59
Abnormal inner temperature
detected
detected
Display appears when the drive temperature
exceeds 70°C.
The power is turned off forcibly.
For 30 minutes after this, all key entries are
disabled. (Fan motor operates at the highest
speed for the first 5 minutes. For the
remaining 25 minutes, fan motor is also
stopped.) The event is saved in memory as
well.
exceeds 70°C.
The power is turned off forcibly.
For 30 minutes after this, all key entries are
disabled. (Fan motor operates at the highest
speed for the first 5 minutes. For the
remaining 25 minutes, fan motor is also
stopped.) The event is saved in memory as
well.
"U59" is displayed for 30 minutes.
U71
HDMI incompatible error
(HDMI incompatible)
(HDMI incompatible)
Display this error when the equipment
(compatible with DVI such as TV, amplifier
etc.) connected to the unit by HDMI is
incompatible with HDCP (High-bandwidth
Digital Content Protection).
(compatible with DVI such as TV, amplifier
etc.) connected to the unit by HDMI is
incompatible with HDCP (High-bandwidth
Digital Content Protection).
U72
HDMI connection error
(communication error)
(communication error)
Display this error when there are any
communication problems with the unit and
the equipments (TV, amplifier, ect.)
connected to the unit by HDMI (or when
there is a problem with the HDMI cable).
The display disappears only when the
connection is released. Neither the button
operation nor the passage of the fixed time
disappear the display.
communication problems with the unit and
the equipments (TV, amplifier, ect.)
connected to the unit by HDMI (or when
there is a problem with the HDMI cable).
The display disappears only when the
connection is released. Neither the button
operation nor the passage of the fixed time
disappear the display.
"U72" display disappears when
error has been solved by Power
OFF/ON of connecting equipment
or by inserting/removing of HDMI
cable.
error has been solved by Power
OFF/ON of connecting equipment
or by inserting/removing of HDMI
cable.
U73
HDMI connection error
(authentication error)
(authentication error)
When authentication error occurs while the
equipments (TV, amplifier, etc.) are
connected by HDMI (or when there is a
problem with the HDMI cable).
The display disappears only when the
connection is released. Neither the button
operation nor the passage of the fixed time
disappear the display.
equipments (TV, amplifier, etc.) are
connected by HDMI (or when there is a
problem with the HDMI cable).
The display disappears only when the
connection is released. Neither the button
operation nor the passage of the fixed time
disappear the display.
"U73" display disappears when
error has been solved by Power
OFF/ON of connecting equipment
or by inserting/removing of HDMI
cable.
error has been solved by Power
OFF/ON of connecting equipment
or by inserting/removing of HDMI
cable.
U76
Connection error
This error is displayed when equipment such
as TVs or amplifiers connected to the unit
with the HDMI cable do not correspond to the
copyright protection. (The BD/DVD video
where the copyright is protected cannot be
played.)
as TVs or amplifiers connected to the unit
with the HDMI cable do not correspond to the
copyright protection. (The BD/DVD video
where the copyright is protected cannot be
played.)
U77
Illegal disc error
This error is displayed when it becomes
impossible to reproduce because of copyright
illegal information.
impossible to reproduce because of copyright
illegal information.
U88
Restoration is operation.
(When the disc is in the disc
tray)
(When the disc is in the disc
tray)
This error is displayed when there is a disc in
the disc tray or abnormality is confirmed
during playback. It is shown that the
restoration to return the main unit operation
normally is operating. It becomes possible to
use as soon as not the breakdown but the
U88 display disappears.
the disc tray or abnormality is confirmed
during playback. It is shown that the
restoration to return the main unit operation
normally is operating. It becomes possible to
use as soon as not the breakdown but the
U88 display disappears.
Display for 30 seconds.
H19
No working Fan Motor
Preserves the Error record in case the Fan
Motor doesn't work at the time of Power-On.
Motor doesn't work at the time of Power-On.
No display
Click on the first or last page to see other SA-BTT790EE / SC-BTT790EEK service manuals if exist.