Panasonic SA-BTT500EB / SA-BTT500EE / SA-BTT500EG / SA-BTT560EB / SA-BTT560EG / SC-BTT500EES Service Manual ▷ View online
5
1.4.
Caution For AC Cord (For EB only)
6
1.5.
Caution For Fuse Replacement
7
1.6.
Safety Part Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by (
These parts are marked by (
) in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts
should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design
without permission of manufacturer.
without permission of manufacturer.
Safety
Ref No.
Part No.
Part Name & Description
Remarks
16
RGRX1006R-A
REAR PANEL
BTT500E
B/EG
16
RGRX1006R-B1
REAR PANEL
BTT500E
E
E
16
RGRX1006R-C
REAR PANEL
BTT560E
B/EG
B/EG
24
RKM0710-S
TOP CABINET
BTT560E
B/EG
B/EG
24
RKM0710A-S
TOP CABINET
BTT500E
B/EE/EG
44
RMZ1280-1
SMPS PCB TOP INSULATOR
101
VQL2P54
LASER CAUTION LABEL
137
RXQ2072
OPTICAL PICK-UP ASS'Y
(E.S.D)
144
VXA9006
BRS1.4P TRV UNIT (WITH OPU)
(E.S.D)
A2
K2CQ2YY00119
AC CORD
BTT500E
E/EG,
E/EG,
BTT560E
G
G
A2
K2CT2YY00097
AC CORD
BTT500E
B,
BTT560E
B
BTT560E
B
A3
VQT4Q16-1
O/I BOOK (Ge)
BTT500E
B,
BTT560E
B,
BTT560E
B
A3
VQT4Q17-1
O/I BOOK (Fr/It/Sp/Du/Sw/Da/
Fin)
Fin)
BTT500E
G,
G,
BTT560E
G
G
A3
VQT4Q18
O/I BOOK (En)
BTT500E
G,
BTT560E
BTT560E
G
A3
VQT4V59-1
O/I BOOK (Ru/Ur)
BTT500E
E
E
PCB10
REP4740G
SMPS P.C.B.
(RTL)
PCB11
REP4740G
AC INLET P.C.B.
(RTL)
DZ5701
D4EAY511A127
ZNR
(E.S.D)
L5701
ELF19H015A
LINE FILTER
L5703
ELF17N011A
LINE FILTER
T5701
ETS40BD166AC
TRANSFORMER
T5751
G4DYZ0000065
TRANSFORMER
PC5702
B3PBA0000579
PHOTO COUPLER
PC5720
B3PBA0000579
PHOTO COUPLER
PC5799
B3PBA0000579
PHOTO COUPLER
PC5901
B3PBA0000579
PHOTO COUPLER
F1
K5D312BNA005
FUSE
IP55002 K5H252Z00003
PROTECTOR
IP55003 K5H252Z00003
PROTECTOR
P5701
K2AA2B000017
AC INLET
R5700
ERJ8GEYJ155V
1.5M 1/4W
R5701
ERJ8GEYJ155V
1.5M 1/4W
C5700
F1BAF1020020
1000pF
C5701
F0CAF104A105
0.1uF
C5702
F0CAF104A105
0.1uF
C5703
F0CAF104A105
0.1uF
C5705
F1BAF1020020
1000pF
8
2 Warning
2.1.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi-
tive (ES) Devices
tive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION:
CAUTION:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
ficient to damage an ES device).
Click on the first or last page to see other SA-BTT500EB / SA-BTT500EE / SA-BTT500EG / SA-BTT560EB / SA-BTT560EG / SC-BTT500EES service manuals if exist.