DOWNLOAD Panasonic CS-BE20TKD / CU-BE20TKD Service Manual ↓ Size: 23.45 MB | Pages: 92 in PDF or view online for FREE

21 

The mounting wall shall be strong and solid enough to prevent it from vibration. 
 

 

 

Model 

Dimension 

1

 

2

 

3

 

4

 

5

 

6

 

BE20***, 
KE25***, BE25***, DE25***, 
KE35***, BE35***, DE35*** 

480 mm 

90 mm 

425 mm 

425 mm 

43 mm 

95 mm 

 

 

 

Model 

Dimension 

1

 

2

 

3

 

4

 

5

 

6

 

KE50***, BE50***, DE50*** 

490 mm 

85 mm 

439 mm 

432 mm 

43 mm 

95 mm 

 
The center of installation plate should be at more than 1 at right and left of the wall. 
The distance from installation plate edge to ceiling should more than 2. 
From installation plate center to unit’s left side is 3. 
From installation plate center to unit’s right side is 4. 
B

 

: For left side piping, piping connection for liquid should be about 5 from this line. 

 

: For left side piping, piping connection for gas should be about 6 from this line. 

1  Mount the installation plate on the wall with 5 screws or more (at least 5 screws). 

(If mounting the unit on the concrete wall, consider using anchor bolts.) 

o

 

Always mount the installation plate horizontally by aligning the marking-off line with the thread and using 
a level gauge. 

2  Drill the piping plate hole with ø70 mm hole-core drill. 

o

 

Line according to the left and right side of the installation plate. 
The meeting point of the extended line is the center of the hole. 
Another method is by putting measuring tape at position as shown in the diagram above. 
The hole center is obtained by measuring the distance namely 128 mm for left and right hole 
respectively. 

o

 

Drill the piping hole at either the right or the left and the hole should be slightly slanting to the outdoor 
side. 

3

4

B

A

C

Ceiling

Wall

Wall

Installation 
plate 

1

2 screw

More than 

1

More than 

1

Measuring Tape

Indoor unit

228 mm

128 mm

228 mm

128 mm

More than 

2

For best strength of 
INDOOR unit installation, 
it is highly recommended 
to locate “ ” at 5 position 
as shown. 

3

4

B

A

C

Ceiling

Wall

Wall

Installation 
plate 

1

2 screw

More than 

1

More than 

1

Measuring Tape

Indoor unit

241.5 mm

128 mm

241.5 mm

128 mm

More than 

2

For best strength of 
INDOOR unit installation, 
it is highly recommended 
to locate “ ” at 5 position 
as shown. 

22 

1  Insert the piping sleeve to the hole. 
2  Fix the bushing to the sleeve. 
3  Cut the sleeve until it extrudes about 15 mm 

from the wall. 

 

 

   

           

 

 When the wall is hollow, please be sure to use the

  sleeve for tube assembly to prevent dangers 
  caused by mice biting the connection cable. 

 

4  Finish by sealing the sleeve with putty or 

caulking compound at the final stage. 
 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Putty or caulking compound

Sleeve for 
tube assembly

Approx. 5 - 7 mm

Bushing for tube assembly

Wall

ø70 mm 
through hole

Indoor

Outdoor

15 mm

23 

 

 

 

 

 
 
 
 
 
 

 
 

 

 
(This can be used for left rear piping and bottom 
piping also.) 

 

•

 Do not turn over the unit without it’s shock absorber during pull out the piping.
It may cause intake grille damage.

 

•

 Use shock absorber during pull out the piping to protect the intake grille from damage.

Intake grille

Piping

pull ou

t the

 pip

in

g

Piping

Shock absorber

pull o

ut t

he

 p

ip

in

g

Install the Indoor Unit

Pull out the Indoor piping

Step-2

Secure the Indoor Unit

Insert the power supply cord and connection cable

Step-1

Step-3

Step-4

• Insert the cables from bottom of the unit through the control board hole until
 

terminal board area.

Install the Indoor Unit

Pull out the Indoor piping

Step-2

Insert the power supply cord and connection cable

Secure the Indoor Unit

Step-1

Step-3

Step-4

• Insert the cables from bottom of the unit through the control board hole until
  terminal board area.

• Use a spring bender or equivalent to bend the piping so that the piping is not 
    crushed.

• When determining the dimensions of the piping, slide the unit all the way to the  
    left on the installation plate.

• Refer to the section “Cutting and flaring the piping”.

Bend the embedded piping

Cut and flare the embedded piping

Replace the drain hose

Pull the connection cable into Indoor Unit

• The power supply cord and indoor unit and outdoor unit connection cable can
  be connected without removing the front grille.

• Please refer to “Connecting the piping” column in outdoor unit section. 
    (Below  steps  are  done after connecting the outdoor piping and gas-leakage 
    confirmation.)

Connect the piping

• Please refer to “Insulation of piping connection” column as mentioned in
  indoor/outdoor unit installation.

Install the Indoor Unit

Secure the Indoor Unit

Insulate and finish the piping

Step-1

Step-2

Step-3

Step-4

Step-5

Step-6

Step-7

Step-8

In case of the cover is cut, keep the cover at the rear 
of chassis as shown in the illustration for future 
reinstallation. 

(Left, right and 2 bottom covers for piping.)

How to keep the cover

Hook the indoor unit onto the upper  
portion of installation plate. (Engage the  
indoor unit with the upper edge of the 
installation plate). Ensure the  hooks are  
properly seated on the installation plate
by moving it in left and right. 

Press the lower left and right side of the unit against 
the installation plate until hooks engages with their 
slot (sound click).

Right Rear piping

Right and Right Bottom piping

Install the indoor unit

Secure the Indoor Unit

Insert the connection cable

Cover for the 
bottom piping

Cover for the 
bottom piping

Tape it with piping in a 

position as mentioned 

in Fig. below.

Cover for 
the right 
piping

Piping

Drain 
hose

Cover for 
the left 
piping

Cover for 
the bottom 
piping

Tape it with piping in a 

position as mentioned 

in Fig. below.

Cover for 
the right 
piping

Piping

Drain hose

Cover for 
the left 
piping

Drain hose

Sleeve for piping hole

Indoor unit

Hooks at installation 
plate

Piping

Cover for piping

Guide 
surface

Connection cable

About 

70 – 80 mm

Connection cable

Gas side piping

Liquid side piping

Drain hose

Installation 
plate

Unit’s hook

To take out the unit, push the          marking at the bottom
unit, and pull it slightly towards you to disengage the hooks
from the unit.

g

n

i

k

r

a

m

 

24 

 

The power supply cord, indoor and outdoor unit connection cable can be connected without removing the front grille. 

1  Install the indoor unit on the installing holder that mounted on the wall. 
2  Open the front panel and grille door by loosening the screw. 
3  Cable connection to the power supply through Isolating Devices (Disconnecting means). 

o

 

Connect approved type polychloroprene sheathed power supply cord 3 x 1.5 mm

2

 (3/4 ~ 1.5HP) or 3 x 

2.5 mm

2

 (2.0HP) type designation 60245 IEC 57 or heavier cord to the terminal board, and connect the 

others end of the cord to Isolating Devices (Disconnecting means). 

o

 

Do not use joint power supply cord. Replace the wire if the existing wire (from concealed wiring, or 
otherwise) is too short. 

o

 

In unavoidable case, joining of power supply cord between isolating devices and terminal board of air 
conditioner shall be done by using approved socket and plug with earth pin rated 15/16A (3/4 ~ 1.5HP) 
or 16A (2.0HP). Wiring work to both socket and plug must follow to national wiring standard. 

4  Bind all the power supply cord lead wire with tape and route the power supply cord via the left escapement. 
5  Connection cable between indoor unit and outdoor unit shall be approved polychloroprene sheathed  

4 x 1.5 mm

2

 (3/4 ~ 1.5HP) or 4 x 2.5 mm

2

 (2.0HP) flexible cord, type designation 60245 IEC 57 or heavier 

cord. Do not use joint connection cable. Replace the wire if the existing wire (from concealed wiring, or 
otherwise) is too short. Allowable connection cable length of each indoor unit shall be 30 mm or less. 

6  Bind all the indoor and outdoor connection cable with tape and route the connection cable via the right 

escapement. 

 
 
 
 
 
 
 
 

 

•

How to pull the piping and drain hose out, in case of the 
embedded piping.

 

•

In case of left piping how to insert the 
connection cable and drain hose.

Rear view for left piping installation

Drain cap

Drain hose

Adjust the piping slightly 
downwards.

Drain hose

Connection cable

 

PVC tube 
for drain 
hose

Indoor unit

100 mm

Piping

Cable

Apply putty or 
caulking material 
to seal the wall 
opening.

Connection cable

Piping

More than 

470 mm

More than 

950 mm

PVC tube (VP-65) for piping 
and connection cable

PVC tube for drain hose (VP-30)

PVC tube for drain 
hose (VP-20)

More than 700 mm

Drain hose 
from main unit

Exchange the drain hose and cap

Cable

45°

Drain 
hose

Piping

Sleeve for piping hole

Drain hose

Piping

Connection cable

More than 950 mm

(For the right piping, follow the same procedure)