LG WT5101HW Service Manual ▷ View online
4
2. INSTALLATION INSTRUCTIONS
2-1. HOW TO ADJUST LEVEL
4
Raise
Lower
CAUTION
• The ventilating openings in the base area must not be obstructed by carpeting.
• Install the washing machine on a level and firm surface, and tilt should be less than 1˚
• Wooden floors may need reinforcing to prevent the normal vibration which occurs with an
• Install the washing machine on a level and firm surface, and tilt should be less than 1˚
• Wooden floors may need reinforcing to prevent the normal vibration which occurs with an
unbalanced load.
• Do not install the washer on an inclined floor.
Improper installation of the washer may cause noise and malfunctioning.
1
Installation area
•
Install the washer on a firm, flat
surface.
•
If the washer is installed on an
unsuitable floor, it could make
considerable noise and vibrate.
unsuitable floor, it could make
considerable noise and vibrate.
2
3
Checking level
•
Open the lid, check if the washer is
correctly leveled by looking down
from the top. If a gap is seen
between the tub and drum, the
washer is not level.
correctly leveled by looking down
from the top. If a gap is seen
between the tub and drum, the
washer is not level.
No shims. It would be dangerous. If the
floor is that far from being level, it is a floor
problem and not a washer problem.
floor is that far from being level, it is a floor
problem and not a washer problem.
Set Leveling feet
•
Loosen the locknuts on 2 front leveling
feet until you can turn the feet with the
included wrench. Turn clockwise to
raise the washer or counterclockwise
to lower it.
feet until you can turn the feet with the
included wrench. Turn clockwise to
raise the washer or counterclockwise
to lower it.
Checking slope
•
If installation surface is tilted, the
washer will vibrate. Do not install
on a sloping floor.
washer will vibrate. Do not install
on a sloping floor.
5
27″
(68.6 cm)
1″
(2.5 cm)
1″
(2.5 cm)
28.
13
/
64
″
(72.1 cm)
4″
(10 cm)
45.
13
/
32
″
(115.3 cm)
55.
13
/
16
″
(141.7 cm)
(with lid
open)
6
7
5
Lower
Raise
Confirming level
•
Place the washer in original position,
confirming the level.
confirming the level.
Horizontal setting
•
Lift the front of the washer and adjust
level by turnings the adjustable legs
clockwise or using the adjusting plate.
level by turnings the adjustable legs
clockwise or using the adjusting plate.
Distance between the drain hose
and the wall
•
Distance between the drain hose and
the wall should be more than 4 inches
(10 cm), and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm)
the wall should be more than 4 inches
(10 cm), and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm)
Do not install the washer in the following places.
•
Where the washer is exposed to direct sunlight.
•
Near a heater or heating appliance.
•
Where the washer is exposed to freezing temperatures.
•
In damp environments such as bathrooms or harmful environments.
1
Attach the water supply hose to the tap.
Push the water supply hose up so that the rubber packing
within the hose can adhere completely to the tap.
within the hose can adhere completely to the tap.
2
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then tighten it by
screwing it to the right.
screwing it to the right.
3
Check water leakage.
After connecting the hose, open the tap to check for
any water leakage.
any water leakage.
Check water leakage.
After connecting the hose, open the tap to check for
any water leakage.
any water leakage.
Connecting Water Supply Hose to the machine
• Connect the water supply hose to inlet valve of
the washing machine, and then lock it by turning
the hose connecting part.
the hose connecting part.
• Check to see if there is a rubber seal inside the
connector.
• A nwe washing machine should be instailed with new
hoses. The old hoses shuld not be reused.
Screw Type
Hot
Cold
Water tap
Rubber Seal
Water Supply Hose
Water Hose
(to water inlet
on washer)
(to water inlet
on washer)
Rubber Seal
Water Hose
(to tap)
(to tap)
Rubber Seal
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting the Water Supply Hose to the water tap, check the hose type and then choose the
correct instruction here under.
correct instruction here under.
7
2-3. CONNECT THE DRAIN HOSE
39" (99 cm)
39" (99 cm)
• Connect the drain hose to the
outlet of the drain pump located at
the rear of the washing machine.
the rear of the washing machine.
• Attach the clip to the drain hose.
And then push it toward the body of
the washing machine as indicated
by the arrow.
the washing machine as indicated
by the arrow.
• Check that the drain hose is hung
up over the edge of the laundry tub.
• Do not use an extension hose.
NOTE :
•
The drain hose should always be properly secured. Failure to properly secure the drain hose
can result in flooding and property damage.
can result in flooding and property damage.
• The end of the drain hose should be placed 39" (99 cm) from the floor.
• The drain must be installed in accordance with any applicable local codes and regulations.
• Make sure that the water lines are not stretched, pinched, crushed, or kinked.
• Do not insert the drain hose more than 12” (30 cm) into the drain pipe to avoid siphoning and
• The drain must be installed in accordance with any applicable local codes and regulations.
• Make sure that the water lines are not stretched, pinched, crushed, or kinked.
• Do not insert the drain hose more than 12” (30 cm) into the drain pipe to avoid siphoning and
odor build-up.
Cable Tie
Cable Tie
WARNING:
• The washer should never be installed or stored in a location subject to freezing temperatures. If the
washer was exposed to freezing temperatures prior to installation, allow it to stand at room
temperature for several hours before use Damage to the water lines and internal mechanisms of
the washer can result.
temperature for several hours before use Damage to the water lines and internal mechanisms of
the washer can result.
• Water supply pressure must be between 14.5 psi and 116 psi (100 ~ 800kPa) If the water supply
pressure is more than 116 psi, a pressure reducing valve must be installed. If you have
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that wate temperature and water pressure remain within the safe limits. Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure. Failure to do
so can result in damage to the machine.
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that wate temperature and water pressure remain within the safe limits. Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure. Failure to do
so can result in damage to the machine.
• Plug the power cord of washer into a properly grounded outlet. Failure to do this can result in shock
or serious injury.