LG WT5101HW Service Manual ▷ View online
1. SPECIFICATIONS
3
Model
Electrical
Inner Tub
Inlet Water Pressure
Rating of Fuse
Spin Speed
Weight
Cycles
Time Delay
Lid Interlock Switch
Child Lock
Softener Dispenser
Detergent Dispenser
Bleach Inlet
Auto Power Off
Smart Rinse™ with Jet Spray
Heater
WT5101HW / WT5101HV
WT5001CW
120VAC@60Hz.
Stainless
14.5 ~ 116 PSI (100 ~ 800 kPa)
125V, 12A for 100~127V/60Hz
1100
±50
145.5 lbs (66kg)
Cotton/Normal, Bulky/Bedding, Heavy Duty, Perm Press Casual, Sanitary, Baby Wear, Tub Clean,
Bright Whites™, Delicates, Pure Color™, Sports Wear, Speed Wash, Wool, Towels
1-18Hr
Magnet Sensor
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
4
2. INSTALLATION INSTRUCTIONS
2-1. HOW TO ADJUST LEVEL
4
Raise
Lower
CAUTION
• The ventilating openings in the base area must not be obstructed by carpeting.
• Install the washing machine on a level and firm surface, and tilt should be less than 1˚
• Wooden floors may need reinforcing to prevent the normal vibration which occurs with an
• Install the washing machine on a level and firm surface, and tilt should be less than 1˚
• Wooden floors may need reinforcing to prevent the normal vibration which occurs with an
unbalanced load.
• Do not install the washer on an inclined floor.
Improper installation of the washer may cause noise and malfunctioning.
1
Installation area
•
Install the washer on a firm, flat
surface.
•
If the washer is installed on an
unsuitable floor, it could make
considerable noise and vibrate.
unsuitable floor, it could make
considerable noise and vibrate.
2
3
Checking level
•
Open the lid, check if the washer is
correctly leveled by looking down
from the top. If a gap is seen
between the tub and drum, the
washer is not level.
correctly leveled by looking down
from the top. If a gap is seen
between the tub and drum, the
washer is not level.
No shims. It would be dangerous. If the
floor is that far from being level, it is a floor
problem and not a washer problem.
floor is that far from being level, it is a floor
problem and not a washer problem.
Set Leveling feet
•
Loosen the locknuts on 2 front leveling
feet until you can turn the feet with the
included wrench. Turn clockwise to
raise the washer or counterclockwise
to lower it.
feet until you can turn the feet with the
included wrench. Turn clockwise to
raise the washer or counterclockwise
to lower it.
Checking slope
•
If installation surface is tilted, the
washer will vibrate. Do not install
on a sloping floor.
washer will vibrate. Do not install
on a sloping floor.
5
27″
(68.6 cm)
1″
(2.5 cm)
1″
(2.5 cm)
28.
13
/
64
″
(72.1 cm)
4″
(10 cm)
45.
13
/
32
″
(115.3 cm)
55.
13
/
16
″
(141.7 cm)
(with lid
open)
6
7
5
Lower
Raise
Confirming level
•
Place the washer in original position,
confirming the level.
confirming the level.
Horizontal setting
•
Lift the front of the washer and adjust
level by turnings the adjustable legs
clockwise or using the adjusting plate.
level by turnings the adjustable legs
clockwise or using the adjusting plate.
Distance between the drain hose
and the wall
•
Distance between the drain hose and
the wall should be more than 4 inches
(10 cm), and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm)
the wall should be more than 4 inches
(10 cm), and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm)
Do not install the washer in the following places.
•
Where the washer is exposed to direct sunlight.
•
Near a heater or heating appliance.
•
Where the washer is exposed to freezing temperatures.
•
In damp environments such as bathrooms or harmful environments.
1
Attach the water supply hose to the tap.
Push the water supply hose up so that the rubber packing
within the hose can adhere completely to the tap.
within the hose can adhere completely to the tap.
2
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then tighten it by
screwing it to the right.
screwing it to the right.
3
Check water leakage.
After connecting the hose, open the tap to check for
any water leakage.
any water leakage.
Check water leakage.
After connecting the hose, open the tap to check for
any water leakage.
any water leakage.
Connecting Water Supply Hose to the machine
• Connect the water supply hose to inlet valve of
the washing machine, and then lock it by turning
the hose connecting part.
the hose connecting part.
• Check to see if there is a rubber seal inside the
connector.
• A nwe washing machine should be instailed with new
hoses. The old hoses shuld not be reused.
Screw Type
Hot
Cold
Water tap
Rubber Seal
Water Supply Hose
Water Hose
(to water inlet
on washer)
(to water inlet
on washer)
Rubber Seal
Water Hose
(to tap)
(to tap)
Rubber Seal
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting the Water Supply Hose to the water tap, check the hose type and then choose the
correct instruction here under.
correct instruction here under.