DOWNLOAD LG WT-Y2K Service Manual ↓ Size: 5.51 MB | Pages: 66 in PDF or view online for FREE

Model
WT-Y2K
Pages
66
Size
5.51 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
wt-y2k.pdf
Date

LG WT-Y2K Service Manual ▷ View online

7
Rubber packing
Screw
Fixed sticker
Rubber packing
Guide plate
Connector
Connector
Fixed sticker
Middle
Connector
Middle
Connector
Water Supply Hose
Pressing rod
Pressing handle
Connector
Middle
connector
Fixed Stiicker
Pressing Handle
Pressing Rod
Water Supply Hose
Separate Middle connector from Water Supply Hose 
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that
the tap can be placed in the middle.
Fixing Connectors to the Tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the
Upper and Middle Connectors. Tighten the
connectors by holding one connector and
twist middle connector to the right.
Connecting  Middle Connector and Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from
middle connector(refer to Step1) and then
join it to the middle connector.
One Touch Type
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
In case the tap is large.
Note
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1. 
If you skip step1, it may cause water leakage.
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
1
2
3
4
5
6
8
Attach the water supply hose to the tap.
Push the water supply hose up so that the
rubber packing within the hose can adhere
completely to the tap.
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and
then tighten it by screwing it to the right.
Check water leakage.
After connecting the hose, open the faucet to
check for any water leakage.
Connect the water supply hose to inlet valve
of the washing machine, and then lock it by
turning the hose connecting part.
Check to see if there is a rubber seal inside 
the connector.
Screw Type
Water Supply Hose
Rubber Packing
H
Rubber seal
Water
tap
Connecting Water Supply Hose to the machine
1
2
3
9
2-3. CONNECT THE DRAIN HOSE
2-4. FLOODING DRAINAGE
For pump model
For non - pump model
Connect the drain hose to 
the outlet of the drain pump
located at the rear of the
washing machine.
Attach the clip to the drain 
hose. And then push it toward
the body of the washing 
machine as indicated by the
arrow.
Check that the drain hose is hung
up over the edge of the laundry tub.
Do not use an extension hose.
Hose
Guide
Within 50mm
0.9~
1.2m
Drain Hose
Holder
Holes for the Holder
Push 
Holes
For Holder
Never lay down the drain hose, as water will be discharged.
Be sure the drain hose is properly routed so it will not kink or lift  from the sink.
The discharge height should be approximately 0.9~1.2m from  the floor.
Connect the drain hose adjusting the length of it not to be dropped. If drain hose
is dropped the drainage could be poor because of blockage in the hose.
Connect the drain hose to the outlet of the 
drain located at the back side of the
washing machine.
Fix the drain hose with the clip.
And then push it toward the body as in the
figure.
Keep it downward while the washing machine  is working.
Ensure the hose is free from kinking.
● 
You machine requires a floor drainage slope (or hole) that will SAFELY DISPOSE of the FULL FLOW of any water that may leak
out should the machine malfunction.
It is therefore the OWNER'S RESPONSIBILITY to make sure this machine is installed in an area with a drain hole (or slope) that
will prevent any possibility of water damage to floor coverings or property.
Do not install the washer where it is directly exposed to sunlight, wind, rain, etc.
Plug the power cord of this washer into a properly installed standard power outlet that is grounded.
Your machine requires a floor drainage slope (or hole) that will SAFELY DISPOSE of the FULL FLOW of any water that may leak
out should the machine malfunction. It is therefore the OWNER’S RESPONSIBILITY to make sure this machine is installed in an
area with a drain hole (or slope) that will prevent any possibility of water damage to floor coverings or property.
Permissible water temperature : Max 70˚C (160˚F)
Permissible water pressure : Max 116psi (800 kpa, 8 kg/cm
2
), Min 4 psi (30 kpa, 0.3 kg/cm
2
)
● 
If water temperature and pressure are greater than above, it may cause damage to the machine. If you have uncontrolled water
temperature and pressure you should fit a temperature and pressure relief valve to ensure that water temperature and water
pressure remain within the safe limits. Consult a plumber or electrician if you are unable to adjust water temperature and pressure.
Do not over tighten the coupling nuts with a tool. Inlets are plastic : Do not strip or crossthread.
CAUTION
10
3. OPERATING INSTRUCTIONS
3-1. IDENTIFICATION OF PARTS
HOT WATER SUPPLY
HOSE 
COLD WATER SUPPLY
HOSE
Make sure the water 
does not leak.
FUNCTION SELECTOR
Powder detergent 
(powder bleach)box
for delayed washing/
softener box
Washing Tub 
stainless steel tub
START/PAUSE
BUTTON
Use to start or stop the 
washing machine 
temporarily.
Anti Rat Base
DRAIN HOSE
For non Pump Model
¥ Keep downward while the 
   washing machine is 
   working.
DRAIN HOSE
For Pump Model
¥ Check out if the drain hose
   is located in the laundry tub 
   before operating the washing 
   machine.
POWER PLUG
If the supply cord is 
damaged, it must be 
replaced by the manufacturer 
or its service agents or 
a similarly qualified person 
in order to avoid a hazard.
SPIN S
PEED IN
DICATO
R
SILEN
T
COLD
HOT
DELA
Y
WOOL
NORMAL
SPEEDY
PRO
GRAM
STAR
T
PAUS
E
POW
ER
JEAN
DELICATE
NO IN
LET
DOOR
 OPEN
DRAIN
 Er.
STAIN
LEVEL
WATER
LEVEL
WATER
TEMP.
WAS
H
RINS
E
MIN
MIN
MIN
SPIN
S        
 M      
  L      
  XL
LIGH
T
HEAV
Y
SOAK
DELAY
/TIME L
EFT
Turbo clean filter
Page of 66
Display

Click on the first or last page to see other WT-Y2K service manuals if exist.