LG WT-R10686 Service Manual ▷ View online
5
28.
13
/
64
″
(72.1 cm)
4″
(10 cm)
55.
13
/
16
″
(141.7 cm)
(with lid
open)
6
7
5
Lower Raise
Confirming level
•
Place the washer in original position,
confirming the level.
Horizontal setting
•
Lift the washer and adjust level by
turnings the adjustable legs clockwise
or using the adjusting plate.
Distance between the drain hose
and the wall
and the wall
•
Distance between the drain hose and
the wall should be more than 4 inches
(10 cm,) and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm.)
■
Do not install the washer in the following places.
•
Where the washer is exposed to direct sunlight.
•
Near a heater or heating appliance.
•
Where the washer is exposed to freezing temperatures.
•
In damp environments such as bathrooms or harmful environments.
Rubber packing
Connector
Water supply hose
1
Untighten the screw
Untighten the screw of the connector so that the tap can be
placed in the middle.
2
Fixing the connector to the tap
Push the upper connector up till the rubber packing is in tight
contact with the tap. Then tighten the 4 screws.
3
4
5
Attach the water supply hose to the connector
Push the water supply hose vertically upwards so that the rubber
seal within the hose can adhere completely to the tap.
Fixing the connector of connector and water supply hose
Attach the water supply hose to the connector
and then tighten it by screwing it to the right.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to check for any water leakage.
In case of water leakage, close the tap and start again from step 1.
Normal Type
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting Water Supply Hose to water tap, check your hose type and choose correct
instruction. Water Supply Hose may vary according to the country.
Make sure connect blue inlet hose to COLD water tab, and orange inlet hose to HOT water tab.
(Normal tab without thread & screw type inlet hose.)
Connecting Water Supply Hose to water tap
Conector
Medio
Etiqueta
Fija
Manija de Presión
Barra de Presión
Barra de Presión
Manguera de Suministro de Agua
Empaque
de Caucho
Tornillo
Etiqueta
Fija
Empaque
de Caucho
Placa Guía
Conector
Conector
Etiqueta
Fijada
Conector
Medio
Conector
Medio
Conector
Manguera de Suministro de Agua
Barra de Presión
Mani
ja
de Presión
Fixed Stiicker
Pressing Handle
Pressing Rod
Pressing Rod
Water Supply Hose
Middle connector
Rubber packing
Screw
Fixed sticker
Guide plate
Connector
Connector
Rubber packing
Connector
Middle
Connector
Pressing handle
Middle
Connector
Fixed sticker
Pressing rod
Water Supply Hose
1
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
2
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the tap can
be placed in the middle.
3
4
5
6
Fixing Connectors to the Tap
Push the upper connector up till the rubber packing is in tight
contact with the tap.
Then tighten the 4 screws.
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors.
Tighten the connectors by holding one connector
and twist middle connector to the right.
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to
the middle connector.
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and start
again from step 1.
If you skip step1, it may cause water leakage.
One Touch Type
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
7
Note
In case the tap is large.
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
8
Water Supply Hose
Rubber Packing
Rubber Packing
Water
tap
Hose connector
Rubber seal
1
Attach the water supply hose to the tap.
Push the water supply hose up so that the rubber
packing within the hose can adhere completely
to the tap.
2
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then tighten
it by screwing it to the right.
3
Check water leakage.
After connecting the hose, open the faucet to
check for any water leakage.
Connecting Water Supply Hose to the machine
Connect the water supply hose to inlet valve of
the washing machine, and then lock it by
turning the hose connecting part.
Check to see if there is a rubber seal inside the
connector.
Screw Type
Click on the first or last page to see other WT-R10686 service manuals if exist.