DOWNLOAD LG WP-830QPB Service Manual ↓ Size: 3.53 MB | Pages: 27 in PDF or view online for FREE

-9-

After removing the back cover, opening the spin dryer
cover, and removing the spin dryer basket, proceed
as follows:

1. Pull out the brake wire assembly from the tub and

also take it out from the brake assembly.(Fig. 21).

4. Unscrew and remove the screws fastening the

base and remove the base assembly.(Fig.22)

2. Disconnect the lead wires of the spin motor.

3. Lay the washing machine on its front side on a

blanket or cardboard.

7. Remove the screws fastening the virbration

damper assemblies 
- Remove the vibration damper assemblies
- Remove the spin motor supporter(Fig.25)

8. Loosen the bolt of the coupling assembly fastening

the motor shaft and pull up the coupling assembly
from the motor shaft.(Fig. 26)

5. Hold the spin motor and unscrew and remove the

screws from the base.(Fig. 23)

6. keep placing the brake spring portion lower, and

remove the spin motor.(Fig. 24)

Fig. 21

Fig. 22

Fig. 23

Fig. 24

Fig. 26

Fig. 25

-10-

2. Disconnect the lead wires.

3. Lay the washing machine on its front side on a

blanket or cardboard.

4. Remove the screws fastening the base and remove

the base from the outcase(Fig. 22).

5. Hold the wash motor, and remove the nuts.

(Fig. 29)

6. Remove the special bolt assemblies and remove

the wash motor from the base.

7. Pull out the damper lowers and damper washers.

8. Loosen the socket bolt fastening the motor pulley

assembly and remove the motor pulley assembly
from the motor.(Fig. 30)

To assemble the wash motor assembly to the base,
reverse the above diassembly procedure.

After removing the back cover and the spin dryer
basket, proceed as follows:

1. Remove the V-belt from the pulsator pulley(Fig. 28).

Fig. 28

Fig. 29

Fig. 31

Fig. 30

9. Remove the screws fastening the brake assembly

and remove the brake assembly(Fig. 27)

To assemble the spin motor, reverse the
disassembly procedure.

Fig. 27

After removing the panel assembly, the safety cover
assembly, the spin dryer basket assembly, the spin
dryer cover, the washing cover, the Q-spring, the
nozzle case, the door switch and the back cover,
proceed as follows:

1. Disconnect the drain hose(Non pump model) or

the drain hose-D(Pump model).

2. Unscrew and remove the screws fasting the spin

dryer cover guide.(Fig. 31)

3. Remove the spin dryer cover guide from the tub.

(Fig. 31)

-11-

4. Unscrew and remove the screw fasting the nozzle

case assembly.(Fig. 32)

5. Remove the nozzle case assembly from the tub.

(Fig. 32)

After removing the back cover and opening the
washing cover, proceed as follows:

1. Take out the pulsator cap with "-" type driver.

(WP-1100Q(P) / WP-1100G(P) only)

2. Loosen the pulsator fixing screw and pull up the

pulsator(Fig. 36).

6. Remove the V-belt from the pulsator pulley(Fig. 28)

7. Unscrew the screws on both sides and pull off the

front panel.(Fig. 33)

8. Unscrew and remove the screws on the front and

the rear.(Fig. 34)

3. Remove the V-belt(Fig. 28).

9. Pull out the washing tub assembly.(Fig. 35)

To assemble the washing tub assembly to the out
case assembly, reverse the above disassembly
procedure.

4. Lay the washing machine on its front side on a

blanket or some cardboard.

5. Unscrew and remove the screws fastening the base

and remove the base assembly(Fig. 22).

Fig. 32

Fig. 33

Fig. 34

Fig. 36

Fig. 35

-12-

6. Unscrew the pulsator pulley fixing bolt and remove

the pulsator pulley(Fig. 37).

7. Unscrew and remove the screws fastening the gear

case assembly at the tub(Fig. 38).

To assemble the gearcase assembly to the tub,
reverse the above disassembly.

After removing the spin dryer basket assembly, refer
to the figures and proceed as follows:

1. Remove the bellows assembly(Fig. 40).

2. Remove the bellows supporter by using slip joint

pliers to the spin tub bottom(Fig. 40).

The assembly procedure is as follows:

1. Insert the bellows assembly into the bellows

supporter(Fig. 41).

2. Fit them by pushing the bellows assembly and the

bellows supporter at the same time in the spin tub
bottom(Fig. 41).

3. Pass the spin shaft through the center hole of the

bellows assembly and insert it into the coupling
assembly(Fig. 41).

1. Don't disassemble three screws fixing the

gear case assembly.

2. Check the assembled condition of the

packing-P at the tub hole is right when you
assembled the gear case assembly(Fig. 39).

The bellows assembly attached to the unit
cannot be removed unless it is torn off.

Tub

Packing-P

Gear case

Bellows assembly

Fig. 37

Fig.38

Fig. 39

Fig. 40

Fig. 41