DOWNLOAD LG WP-750RP Service Manual ↓ Size: 4.87 MB | Pages: 27 in PDF or view online for FREE

After removing the back cover, opening the spin dryer cover, and removing the spin dryer basket,
proceed as follows:

1. Remove the brake wire holder-A in the direction of 

the arrow (Fig. 22).

10. Loosen the fixing bolt fastening the motor shaft

and pull up the coupling assembly (Fig. 28).

11. Remove the screws fastening the brake assembly

and remove the brake assembly (Fig. 29).

To assemble the spin motor, reverse the
disassembly procedure.

2. Separate the brake wire assembly from the brake

wire holder (Fig.23).

3. Take out the brake wire assembly from the brake

assembly (Fig. 24).

Fig. 22

Fig. 23

Fig. 24

7. Hold the spin motor and remove the three hooks

from the base (Fig. 26).

8. Remove the spin motor.

9. Remove the screws fastening the vibration damper

assemblies and remove the vibration damper
assemblies (Fig. 27).

4. Disconnect the lead wires and remove the V-belt.

5. Lay the washing machine on its front side on a

blanket or cardboard.

6. Remove the screws fastening the base and

remove the base from the cabinet (Fig. 25).

Jig Push

Fig. 25

Fig. 26

Fig. 27

Fig. 28

Fig. 29

2. Disconnect the lead wires.

3. Lay the washing machine on its front side on a

blanket or cardboard.

4. Romove the screws fastening the base and

remove the base from the cabinet (Fig. 31).

5. Remove the screws and the washers, remove the

wash motor and remove the wash motor damper
(Fig. 32).

6. Loosen the socket bolt of the motor pulley

assembly and pull up the motor pulley assembly
from the motor.

To assemble the wash motor, reverse disassembly
procedure.

After removing the back cover and the spin dryer
basket, proceed as follows:

1. Remove the V-belt from the pulsator pulley (Fig. 30).

Fig. 30

Fig. 31

Fig. 32

Fig. 33

1. Remove the screws fastening the top cover and

remove the top cover from the cabinet.

After removing the panel assembly, the safety cover
assembly, the spin dryer basket assembly, the spin dryer
cover, the washing cover, the Q-spring, top cover assembly,
v-belt the door switch and the back cover, proceed as follows:

1. Lay the front side on a blanket or cardborad.

After removing the back cover and opening the washing
cover, proceed as follows:

1. Loosen the pulsator fixing screw and pull up the

pulsator(Fig. 36).

2. Disconnect the drain hose or the drain hose-D

(Pump model).

3. Remove the screws washing Tub(cabinet) (Fig. 35).

3. Unscrew and remove the screws fastening the

base and remove the base from the cabinet.

4. Lay the washing machine on its front side on a

blanket or some cardboard and remove the base
(Fig. 38).

To assemble the washing Tup(cabinet), reverse the
disassembly procedure.

Apply adhesive on hose joint to prevent
water leaks.

Fig. 34

Fig. 35

Fig. 36

Fig. 37

Fig. 38

Nut

5. Unscrew the pulsator pulley fixing bolt, the nut,

remove the pulsator pulley (Fig. 39).

6. Unscrew and remove the screws fastening the

P.shaft assembly at the cabinet (Fig. 40).

To assemble the P.shaft assembly (Gear case assembly)
to the cabinet, reverse the above disassembly.

After removing the spin dryer basket assembly, refer
to the figures and proceed as follows:

1. Remove the bellows assembly (Fig. 42).

2. Remove the bellows supporter by using slip joint

pliers to the spin tub bottom (Fig. 42).

The assembly procedure is as follows:

1. Insert the bellows assembly into the bellows

supporter (Fig. 43).

2. Fit them by pushing the bellows assembly and the

bellows supporter at the same time in the spin tub
bottom (Fig. 43).

3. Pass the spin shaft through the center hole of the

bellows assembly and insert it into the coupling
assembly (Fig. 43).

1. Don't disassemble three screws fixing the

P.shaft assembly.

2. Check the assembled condition of the

packing-P at the cabinet hole is right when
you assembled the P.shaft assembly(Fig. 41).

The bellows assembly attached to the unit
cannot be removed unless it is torn off.

Fig. 39

Fig. 40

Fig. 41

Fig. 42

Fig. 43