LG WP-1350RS Service Manual ▷ View online
25 mm
-9-
4-4. Spin Motor replacement
After removing the back cover, opening the spin dryer
cover, and removing the spin dryer basket, proceed
as follows:
1. Remove the brake wire holder-A in the direction of
1. Remove the brake wire holder-A in the direction of
the arrow.(Fig. 21).
Brake wire assembly
2. Separate the brake wire assembly from the brake
wire holder.(Fig.22)
7. Hold the spin motor and remove the three hooks
from the base(Fig. 25).
8. Remove the spin motor.
9. Remove the screws fastening the vibration damper
assemblies and remove the vibration damper
assemblies(Fig. 26).
3. Take out the brake wire assembly from the brake
assembly.(Fig. 23)
4. Disconnect the lead wires and remove the V-belt.
5. Lay the washing machine on its front side on a
5. Lay the washing machine on its front side on a
blanket or cardboard.
6. Remove the screws fastening the base and remove
the base from the outcase(Fig. 24).
Fig. 21
Fig. 22
Fig. 23
Fig. 24
Fig. 25
Fig. 26
Jig
Pu
sh
-10-
Fig. 28
Fig. 29
Fig. 32
Fig. 30
Fig. 31
Lower bolt
Fig. 27
10. Loosen the fixing bolt fastening the motor shaft
and pull up the coupling assembly(Fig. 27).
2. Disconnect the lead wires.
3. Lay the washing machine on its front side on a
3. Lay the washing machine on its front side on a
blanket or cardboard.
4. Remove the screws fastening the base and remove
the base from the outcase(Fig. 30).
5. Remove the screws and the washers, remove the
wash motor and remove the wash motor
damper(Fig. 31).
6. Loosen the socket bolt of the motor pulley
assembly and pull up the motor pulley assembly
from the motor.
To assemble the wash motor, reverse disassembly
procedure.
11. Remove the screws fastening the brake assembly
and remove the brake assembly(Fig. 28).
To assemble the spin motor, reverse the disassembly
procedure.
After removing the back cover and the spin dryer
basket, proceed as follows:
1. Remove the V-belt from the pulsator pulley(Fig. 29).
1. Remove the V-belt from the pulsator pulley(Fig. 29).
4-5. Wash Motor Replacement
-11-
4-6. Washing Tub Assembly
replacement
After removing the panel assembly, the safety cover
assembly, the spin dryer basket assembly, the spin
dryer cover, the washing cover, the Q-spring, the
nozzle case, the door switch and the back cover,
proceed as follows:
1. Disconnect the drain hose or the drain hose-D
1. Disconnect the drain hose or the drain hose-D
(Pump model).
2. Remove the V-belt from the pulsator pulley(Fig. 29).
4-7. Gear Case Assembly
replacement
After removing the back cover and opening the
washing cover, proceed as follows:
1. Take out the pulsator cap with "-" type driver.
2. Loosen the pulsator fixing screw and pull up the
1. Take out the pulsator cap with "-" type driver.
2. Loosen the pulsator fixing screw and pull up the
pulsator(Fig. 36).
3. Remove the V-belt(Fig. 29).
4. Lay the washing machine on its front side on a
4. Lay the washing machine on its front side on a
blanket or some cardboard.
5. Unscrew and remove the screws fastening the base
and remove the base assembly(Fig. 37).
Fig. 36
Fig. 37
Fig. 33
3. Unscrew and remove the screws fasting the spin
dryer cover guide.(Fig. 33)
4. Remove the spin dryer cover guide from the tub.
(Fig. 33)
5. Unscrew the screws on both sides and pull off the
front panel.(Fig. 34)
6. Remove the screws on the front and the rare
and pul it out.(Fig. 35)
Fig. 34
Fig. 35
-12-
Nut
6. Unscrew the pulsator pulley fixing bolt, the nut,
remove the pulsator pulley (Fig. 38)
7. Unscrew and remove the screws fastening the gear
case assembly at the tub(Fig. 39).
To assemble the gearcase assembly to the tub,
reverse the above disassembly.
After removing the spin dryer basket assembly, refer
to the figures and proceed as follows:
1. Remove the bellows assembly(Fig. 41).
2. Remove the bellows supporter by using slip joint
1. Remove the bellows assembly(Fig. 41).
2. Remove the bellows supporter by using slip joint
pliers to the spin tub bottom(Fig. 41).
Bellows assembly
The assembly procedure is as follows:
1. Insert the bellows assembly into the bellows
1. Insert the bellows assembly into the bellows
supporter(Fig. 42).
2. Fit them by pushing the bellows assembly and the
bellows supporter at the same time in the spin tub
bottom(Fig. 42).
3. Pass the spin shaft through the center hole of the
bellows assembly and insert it into the coupling
assembly(Fig. 42).
NOTE
1. Don't disassemble three screws fixing the
gear case assembly.
2. Check the assembled condition of the
packing-P at the tub hole is right when you
assembled the gear case assembly(Fig. 40).
NOTE
The bellows assembly attached to the unit
cannot be removed unless it is torn off.
Tub
Packing-P
Gear case
4-8. Bellows Assembly Replacement
Fig. 38
Fig.39
Fig. 40
Fig. 41
Fig. 42
Click on the first or last page to see other WP-1350RS service manuals if exist.