DOWNLOAD LG WP-1310QB Service Manual ↓ Size: 5.51 MB | Pages: 27 in PDF or view online for FREE

Model
WP-1310QB
Pages
27
Size
5.51 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
wp-1310qb.pdf
Date

LG WP-1310QB Service Manual ▷ View online

-6-
4. DISASSEMBLY INSTRUCTIONS
4-1. Panel Assembly replacement
1. Remove the screws fastening the back cover and
remove the back cover(Fig. 1).
NOTE
Before attempting to replace or adjust any
part of the washing machine, disconnect the
electrical power supply from the wall outlet.
NOTE
• When replacing the panel assembly, fix the
plunger valve strap properly.
• Securely solder connecting lead wires, or
used connectors and insulate well to
prevent overheating.
2. Remove the vinyl tape fastening the lead wires
closed connector to the plunger valve assembly and
disconnect the lead wires(Fig. 2).
4. Remove the screws fastening the panel(Fig. 4).
5. Lift up the panel assembly and lay it down on the
top(Fig. 5).
To assemble the panel assembly, reverse the
disassembly procedure.
3. Disconnect the plunger valve strap from the plunger
valve rod(Fig. 3).
Rod
Plunger valve strap
Fig. 1
Fig. 2
Fig. 4
Fig. 3
Fig. 5
Fig. 6
Fig. 8
❒  
Water supply system replacement
1. Pull out the knobs(Fig. 6)
3. Remove the switch body from the panel.
4. Push the supply selector guide in the direction of
the arrow(Fig. 8).
To assemble the water supply system to the switch
body, reverse the above disassembly procedure.
2. Pull out the supply select hose from the supply
select guide(Fig. 7).
Supply select guide
Fig. 7
-7-
2. Remove the screws and separate the switch body
from the panel(Fig. 10).
3. Remove the spin timer by pushing the claw holding
the spin timer in the direction of the arrow(Fig. 11).
To assemble the timers to the switch body, reverse
the disassembly procedure.
❒  
Mini Switch replacement
(Pump model only)
1. Pull out the terminals and remove the screw
fastening the mini switch(Fig. 14).
2. Separate the mini switch from the switch body(Fig. 14).
To assemble the mini switch to the switch body,
reverse the disassembly procedure.
Fig. 10
Fig. 9
Fig. 11
Fig. 14
❒  
Timer replacement
1. Pull out the knobs(Fig. 9)
To assemble the drain select arm to the switch body,
reverse the disassembly procedure.
❒ 
Drain Select Arm replacement
1. Disconnect the plunger valve strap from the drain
select arm(Fig. 12).
2. Lift the drain select arm in the direction of arrow and at
the same time rotate the drain select arm in the direction
of the white arrow until the hook of the drain select arm
matches the groove of the switch body(Fig. 13).
Drain select arm
Plunger valve strap
Fig. 12
Fig. 13
Back side
Front side
4. Remove the screw fastening the cycle timer, pull
out the terminals from the buzzer and remove the
cycle timer(Fig. option1).
Fig. option
-8-
4-2. Spin Dryer Cover replacement
After removing the back cover, the panel assembly,
proceed as follows:
1. Open the spin dryer cover and separate  brake wire
strap from the brake wire assembly (Fig. 15).
Brake wire starp
Brake wire assembly
4-3. Spin Dryer Basket Assembly
replacement
After removing the back cover, proceed as follows:
1. Take hold of the front of the safety cover-1. 
2. Pull the tub by the other hand.
3. Pull the safety cover-1 upward.(fig. 18)
Safety cover-1
Safety cover-2
 Spin dryer cover
2. Remove the Q-spring(Fig. 16).
3.Remove the screw fastening the door switch and
remove the door switch(Fig. 16).
4. Remove the spin dryer cover by widening between the
hinge hole of the tub and the hinge of the spin dryer
cover and pulling up the spin dryer cover(Fig. 17).
5. Loosen the fixing bolt of the coupling assembly
fastening the spin shaft(Fig. 19).
6. Pull out completely the spin basket assembly(Fig. 20).
To assemble the spin dryer cover assembly, reverse
the disassembly procedure.
To assemble the spin dryer basket assembly, reverse
the disassembly procedure.
Fig.15
Fig. 16
Fig.17
Fig. 18
Fig. 19
Fig. 20
-9-
4-4. Spin Motor replacement
After removing the back cover, opening the spin dryer
cover, and removing the spin dryer basket, proceed
as follows:
1. Remove the brake wire holder-A in the direction of
the arrow.(Fig. 21).
Brake wire assembly
2. Separate the brake wire assembly from the brake
wire holder.(Fig.22)
7. Hold the spin motor and remove the three hooks
from the base(Fig. 25).
8. Remove the spin motor.
9. Remove the screws fastening the vibration damper
assemblies and remove the vibration damper
assemblies(Fig. 26).
3. Take out the brake wire assembly from the brake
assembly.(Fig. 23)
4. Disconnect the lead wires and remove the V-belt.
5. Lay the washing machine on its front side on a
blanket or cardboard.
6. Remove the screws fastening the base and remove
the base from the outcase(Fig. 24).
Fig. 21
Fig. 22
Fig. 23
Fig. 24
Fig. 25
Fig. 26
Page of 27
Display

Click on the first or last page to see other WP-1310QB service manuals if exist.