DOWNLOAD LG WP-12123SD Service Manual ↓ Size: 10.36 MB | Pages: 24 in PDF or view online for FREE

-5-

3. CONTROLS LOCATION

3-1. NAMES OF EACH P ARTS

3

4

6

8

9

10
11

12

13

14

(for pump model)

13

7

5

2

1

(1) Panel
(2) Panel deco
(3) Washing cover
(4) Water supply selector lever
(5) Overflow filter
(6) Wash tub
(7) Pulsator(with punch+3 more)
(8)Spin dryer cover

Spinning will stop if the cover is opened
during operation.
Spinning will not start unless the cover is
closed.

(9) Safety cover-2
(10) Spin dryer basket
(11) Safety cover-1
(12) Earth wire

(only on models with a two-prong plug)

(13) Drain hose
(14) Power supply cord

3-2. NAMES OF CONTROL PANEL

(1) Water Supply Inlet : Connect the inlet hose from the water faucet to feed water to the tub.
(2) Wash Timer : Select the desired time for washing (~15 min) or soaking (~35 min).

(3) Wash Program : Set the selector to "Gentle", "Normal", "Strong" according to kinds and quantity of the laundry.

(4) Drain Selector

Non pump model : Select "Wash Rinse" for washing and rinsing, and "Drain" to drain the water out of the wash tub.

(5) Spin T imer : Select the desired time for spinning .
(6) Water Supply Selector : Set the water supply selector lever to "W ASH" for washing and rinsing, to "SPIN"

for interim spin rinse.

WASH

(7) Buzzer :It is electrically operated to facilitate you to know the completion of washing cycle.

-6-

1. Remove the screws fastening the back cover and

remove the back cover(Fig. 1).

Before attempting to replace or adjust any

part of the washing machine, disconnect the

electrical power supply from the wall outlet.

• When replacing the panel assembly, fix the

plunger valve strap properly.

• Securely solder connecting lead wires, or

used connectors and insulate well to

prevent overheating.

2. Remove the vinyl tape fastening the lead wires

closed connector to the plunger valve assembly and

disconnect the lead wires(Fig. 2).

4. Remove the screws fastening the panel(Fig. 4).

5. Lift up the panel assembly and lay it down on the

top(Fig. 5).

To assemble the panel assembly, reverse the

disassembly procedure.

3. Disconnect the plunger valve strap from the plunger

valve rod(Fig. 3).

Rod

p

a

rt

s 

e

vl

a

v

 r

e

g

n

u

l

P

Fig. 1

Fig. 2

Fig. 4

Fig. 3

Fig. 5

Fig. 6

Fig. 8

   Water supply system replacement

1. Pull out the knobs(Fig. 6)

3. Remove the switch body from the panel.
4. Push the supply selector guide in the direction of

the arrow(Fig. 8).

To assemble the water supply system to the switch

body, reverse the above disassembly procedure.

2. Pull out the supply select hose from the supply

select guide(Fig. 7).

Supply select guide

Fig. 7

Timer replacement

q

Pull out the knobs (Fig. 9)

1.

Remove the screws and separate the switch body
from the panel (Fig. 10).

2.

Pull out the terminals from the buzzer and remove
the Soak timer (Fig. 11) by removing the screw.

3.

Remove the spin timer by pushing the claw holding
the spin timer in the direction of the arrow (Fig. 12).

4.

To assemble the timers to the switch body, reverse
the disassembly procedure.

-7-

Fig. 12

Fig. 11

Fig. 10

Fig. 9

Buzzer replacement

q

Pull out the terminals from the buzzer.

1.

Remove the buzzer by pushing the claw & pulling
the buzzer in direction of the arrow.

2.

To assemble the buzzer to the switch body, reverse
the disassembly procedure.

Drain Select Arm replacement

q

Disconnect the plunger valve strap from the drain
select arm (Fig. 14).

1.

Lift the drain select arm in the direction of arrow and at
the same time rotate the drain select arm in the direction
of the white arrow until the hook of the drain select arm
matches the groove of the switch body (Fig. 15).

2.

To assemble the drain select arm to the switch body,
reverse the disassembly procedure.

Fig. 13

Fig. 14

Front side

Back side

Drain select arm

Plunger valve strap

Fig. 15

Spin Timer

Soak Timer

-8-

After removing the back cover, the panel assembly,

proceed as follows:
1. Open the spin dryer cover and separate  brake wire

strap from the brake wire assembly (Fig. 15).

B

p

r

a

t

s

 

e

ri

w

 

e

k

a

r

B

yl

b

m

e

s

s

a

 

e

ri

w

 

e

k

a

r

After removing the back cover, proceed as follows:
1. Take hold of the front of the safety cover-1. 
2. Pull the tub by the other hand.
3. Pull the safety cover-1 upward.(fig. 18)

Safety cover-1

Safety cover-2

 Spin dryer cover

2. Remove the Q-spring(Fig. 16).
3.Remove the screw fastening the door switch and

remove the door switch(Fig. 16).

4. Remove the spin dryer cover by widening between the

hinge hole of the tub and the hinge of the spin dryer

cover and pulling up the spin dryer cover(Fig. 17).

5. Loosen the fixing bolt of the coupling assembly

fastening the spin shaft(Fig. 19).

6. Pull out completely the spin basket assembly(Fig. 20).

To assemble the spin dryer cover assembly, reverse

the disassembly procedure.

To assemble the spin dryer basket assembly, reverse

the disassembly procedure.

Fig.15

Fig. 16

Fig.17

Fig. 18

Fig. 19

Fig. 20