DOWNLOAD LG WP-1051 Service Manual ↓ Size: 4.98 MB | Pages: 23 in PDF or view online for FREE

(1)

 

Wash Cover

(2) Water Supply Selector
(3) Over Flow Filter
(4) Rotation Filter-C
(5) Water Fall
(6) Tub(Cabinet)
(7) Roller Pulsator

(9) Spin dryer cover

Spinning will stop if the cover is opened
during operation.
Spinning will not start unless the cover is
closed.

(8)  Drain  Hose

(11) Spin Dryer Basket

(10) Safety Cover-1

(12) Earth Wire

(only on models with a two-prong plug)

(13) Stainer
(14) Power Cord

(1) Water supply inlet: Connect the inlet hose from the water faucet to feed water to the tub.
(2) Wash Timer: Select the desired time for washing or rinsing.
(3) Wash Program: Set the selector to "GENTLE", "NORMAL", "STRONG" according to kinds and quantity of the laundry.
(4) Drain Selector : Select "WASH-RINSE" for washing and rinsing, and "drain" to drain the water out of the wash tub.
(5) Spin Timer: Select the desired time for spinning.
(6) Water Selector: Set the supply select lever to "WASH" for washing and rinsing, to "SPIN" for interim spin rinse.

1

8

9

10

11

12

13

14

2

3

4

5

6

7

2

3

4

5

6

1

WASH

7.0

kg 

WP-1051

1. Remove the screw fastening the back cover (Fig. 1).

Before attempting to replace or adjust any part of the washing machine, disconnect the electrical
power supply from the wall outlet.

•  When replacing the panel assembly, fix the

plunger valve strap properly.

•  Securely solder connecting lead wires, or

used connectors and insulate well to
prevent overheating.

5. Remove the screws fastening the panel (Fig. 5).

6. Lift up the panel assembly and lay it down on the top (Fig. 6).

To assemble the panel assembly, reverse the disassembly procedure.

1. Pull out the knobs (Fig. 7).

2. Pull out the supply select hose from the supply select

guide (Fig. 8).

Supply select guide

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 1

Fig. 2

2. Pull out the back cover (Fig. 2).

3. Remove the vinyl tape fastening the lead wires

closed connector to the plunger valve assembly and
disconnect the lead wires (Fig. 3).

4. Disconnect the plunger valve strap from the plunger

valve rod (Fig.4).

2. Remove the screws and separate the switch body

from the panel (Fig. 11).

3. Remove the spin timer by pushing the claw holding

the spin timer in the direction of the arrow (Fig. 12).

To assemble the timers to the switch body, reverse
the disassembly procedure.

q

1. Pull out the knobs (Fig. 10).

To assemble the drain select arm to the switch body,
reverse the disassembly procedure.

In the same time rotate the drain select arm in the
direction of the arrow until the hook of the drain select
arm matches the groove of the switch body (Fig. 14).

q

1. Disconnect the plunger valve strap from the drain

select arm (Fig. 13).

Back side

Front side

4. Remove the screw fastening the cycle timer

and

remove the

cycle timer(Fig. option1).

Fig. option1

3. Remove the switch body from the panel.

4. Push the supply selector guide in the direction of

the arrow (Fig. 9).

To assemble the water supply system to the switch
body, reverse the above disassembly procedure.

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Fig. 13

Fig. 14

 

 

 

 

After removing the back cover, disconnect plunger
valve strap from plunger valve rod, remove panel
assembly, remove SD cover then proceed as follows :

1. Loosen  the fixing bolt of coupling assembly

fastening the spin shaft (Fig. 18).

2. Remove the Q-spring (Fig. 16).

3.Remove the screw fastening the door switch and

remove the door switch (Fig. 16).

4. Remove the spin dryer cover by widening between the

hinge hole of the top cover and the hinge of the spin
dryer cover and pulling up the spin dryer cover (Fig. 17).

2. Remove the screws fastening the top cover and remove

the top cover from the cabinet (Fig. 32).

4. Pull out completely the spin basket assembly (Fig. 20).

To assemble the spin dryer cover assembly, reverse
the disassembly procedure.

Fig. 17

Fig. 16

Fig. 15

Fig. 18

 

Fig. 20

After removing the back cover and panel assembly
proceed as follows:

1. Open the spin dryer cover and separate  brake wire

strap from the brake wire assembly (Fig. 15).

3. Take hold of the front of the safety cover-1. Insert screw

drive (- Type) into the hook position. Pull the safety
cover-1 upward (Fig. 19).

Fig. 19

 

To assemble the spin dryer basket assembly, reverse
the disassembly procedure.