DOWNLOAD LG WM2650RD Service Manual ↓ Size: 5.38 MB | Pages: 57 in PDF or view online for FREE

8. TROUBLESHOOTING

If you press the START/PAUSE button when an error is displayed, any error except            will
disappear and the machine will go into the pause status.
In case of            ,           ,            if the error is not resolved within 20 seconds, or the in case of other
errors, if the error is not resolved within 4 minutes, power will be turned off automatically and the error
code will blink. But in the case of          , power will not be turned off.

8-1. SAFETY CAUTION

There’s built-in AC 120V and DC power in output terminal of PWB assembly in common. Be careful
electric shock when disconnecting parts while trouble shooting. (Wear Electro Static Discharge gloves
when working.)
After cutting off the power when changing PWB assembly, disconnect or assemble.
Be careful static when handling PWB assembly, and use Electro Static Discharge plastic pack when
delivering or keeping it.

WATER INLET

ERROR

• Correct water level (24.6kHz) is not reached within 

8 minutes after water is supplied or it does not reach

the preset water level within 20 minutes.

UNBALANCE

ERROR

• The load is too small.

• The appliance is tilted.

• Laundry is gathered to one side.

• Non distributable things are put into the drum.

DRAIN ERROR

• Not fully drained within 10 minutes.

OVERFLOW ERROR

• Water is overflowing. 

(water level frequency is over 21.3kHz).

If              is displayed, the drain pump will 

operate to drain the water automatically.

PRESSURE SENSOR

ERROR

• The PRESSURE SENSOR ASSEMBLY is out of

order.

• When water level frequency maintain condition of

below 10 kHz and over 30 kHz.

DOOR OPEN ERROR

• Door not all the way closed.

• Loose electrical connections at Door switch and

PWB Assembly.

• The DOOR SWITCH ASSEMBLY is out of order.

HEATING ERROR

• The THERMISTOR is out of order.

8-2. ERROR MODE SUMMARY

LOCKED MOTOR

ERROR

EEPROM ERROR

• The connector (3-pin, male, white) in the MOTOR

HARNESS is not connected to the connector (3-pin,

female, white) of STATOR ASSEMBLY.

• The electric contact between the connectors (3-pin,

male, white) in the MOTOR HARNESS and 4-pin,

female, white connector in the MAIN PWB

ASSEMBLY is bad or unstable.

• The MOTOR HARNESS between the STATOR

ASSEMBLY and MAIN PWB ASSEMBLY is cut

(open circuited).

• The hall sensor is out of order/defective.

• EEPROM is out of order.

Displayed only when the START/PAUSE button is

first pressed in the Load Test Mode.

POWER FAILURE

• After the power supply is stopped while washing

machine is working, the power is supplied rapidly. 

pšGGGGGGGGGGGGGGGGG‹š—“ˆ Œ‹f

~Œ•G –œG—™ŒššG‰–›
~hzoVypuzl ‰œ››–•Gˆ•‹
klsh€ ~hzo ‰œ››–•
š”œ“›ˆ•Œ–œš“ S
šG›ŒGžˆ›Œ™G“ŒŒ“G™Œ˜œŒ•Š 
‰Œ“–žGY[U]G’o¡f

pšG“›Œ™G•“Œ›Gˆ“ŒGŠ“–ŽŽŒ‹
ž›G–™ŒŽ•G”ˆ›Œ™ˆ“f

pšG›ŒGŠ–••ŒŠ›–™GŠ–••ŒŠ›Œ‹G›–
•“Œ›Gˆ“ŒGˆššŒ”‰“ 
‹šŠ–••ŒŠ›Œ‹G–™
‹šˆššŒ”‰“Œ‹f

pšG™Œšš›ˆ•ŠŒG‰Œ›žŒŒ•
ŒˆŠG›Œ™”•ˆ“G–Gpusl{
}hs}lGhzzltis€
WU_TXUYG’

˟f

OyŒŒ™G›–G`T\G•“Œ›Gˆ“Œ
ˆššŒ”‰“ UP

j“Œˆ•G–™
™Œ—“ˆŠŒG›ŒG“›Œ™U

jŒŠ’G›ŒGhpy
johtily
ˆ•‹G›ŒG›œ‰Œ
OŠ“–ŽŽŒ‹PU

yŒŠ–••ŒŠ›G–™
™Œ—ˆ™
›ŒGŠ–••ŒŠ›–™U

yŒ—“ˆŠŒG›Œ
pusl{G}hs}l
hzzltis€U

pšG›ŒG–“›ˆŽŒG–G›ŒG•“Œ›
ˆ“ŒGŠ–••ŒŠ›–™GXYWG}Ghjf
OjŒŠ’G›ŒGˆ““G›Œ™”•ˆ“G–

pusl{G}hs}lGhzzltis€
ž“ŒG›ŒG—–žŒ™GšG–•UP

yŒ—“ˆŠŒG›Œ
pusl{G}hs}l
hzzltis€U

pšG›ŒGŠ–••ŒŠ›–™GŠ–••ŒŠ›Œ‹G›–
thpuGw~iGˆššŒ”‰“ 
‹šŠ–••ŒŠ›Œ‹G–™G‹šT
ˆššŒ”‰“Œ‹fOuhYSGuh[SGisZP

yŒŠ–••ŒŠ›G–™
™Œ—ˆ™
›ŒGŠ–••ŒŠ›–™U

pšGl“ŒŠ›™Šˆ“GŠ–••ŒŠ›–•
Š–™™ŒŠ›f

OyŒŒ™G›–G`T\Gž™•ŽG‹ˆŽ™ˆ”P

yŒ—“ˆŠŒG›Œ
thpuGohyulzzU

h›Œ™GŠŒŠ’•ŽGŠ–••ŒŠ›–™S
šG›ŒGžˆ›Œ™G“ŒŒ“G™Œ˜œŒ•Š 
‰Œ“–žGY[U]G’o¡f

yŒ—“ˆŠŒG›ŒGthpuGw~i
hzzltis€U

‚u–›Œ„Gl•™–•”Œ•›ˆ“GšˆŒ› GŠŒŠ’G“š›
XP u–Gžˆ›Œ™G›ˆ—G“Œˆ’ˆŽŒ
YP u–Gžˆ›Œ™G›ˆ—G™ŒŒ¡Œ
ZP u–GŒ•›ˆ•Ž“Œ”Œ•›G–Gžˆ›Œ™Gšœ——“ G–šŒ
[P u–Gžˆ›Œ™Gš–™›ˆŽŒ
\P u–Gš™•’ˆŽŒG–•Gžˆ›Œ™Gšœ——“ G–šŒG‹œŒG›–

ˆG—–šš‰“ŒG”šœšŒG–G–›Gˆ•‹GŠ–“‹Gžˆ›Œ™

]PGu–Gžˆ›Œ™Gšœ——“ G–šŒG“Œˆ’ˆŽŒ

jŒŠ’G›Œ
wylzz|yl
z~p{joU

_T[UG{yv|islzovv{punG~p{oGlyyvy