LG WM2140CW Service Manual ▷ View online
21
NO
YES
YES
YES
YES
NO
NO
NO
NO
YES
BL
WH
WH
WH
WH
RD
BL
BL
BL
OR
RD
BL
(1)
BL
WH
WH
WH
WH
RD
BL
BL
BL
OR
RD
BL
(2)
Is the supplied voltage 120 V AC?
Is the voltage between the pins of 2 FILTER
ASSEMBLY connector 120 V AC?
ASSEMBLY connector 120 V AC?
Is the LED (1) on?
Are the connectors (2) on the PWB loose?
Is wire of the DISPLAY PWB ASSEMBLY
broken?
broken?
Replace DISPLAY PWB ASSEMBLY
or repair wire.
or repair wire.
Check the fuse or reset
the circuit breaker.
the circuit breaker.
Replace the FILTER
ASSEMBLY (CIRC).
ASSEMBLY (CIRC).
Replace MAIN PWB
ASSEMBLY.
ASSEMBLY.
Reconnect.
Replace the MAIN PWB
ASSEMBLY.
ASSEMBLY.
NO POWER
8-2. FAULT DIAGNOSIS AND TROUBLESHOOTING
1. Be careful of electric shock if disconnecting parts while troubleshooting.
2. First of all, check the connection of each electrical terminal with the wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, reinsert the connectors correctly.
CAUTION
22
23
If it still has severe vibration and noise, regulate a specific spin speed that generates excessive vibration and
noise as follows:
1) Put an unbalance part (rubber) inside of the drum.
2) Start the QC test mode (Refer to section 7-2).
3) Press Delay Wash button, then '
1) Put an unbalance part (rubber) inside of the drum.
2) Start the QC test mode (Refer to section 7-2).
3) Press Delay Wash button, then '
' is displayed.
4) Press the Spin Speed button repeatedly to select EXTRA HIGH.
5) Press the Start/Pause button.
6) Press the Signal button repeatedly to set spin speed (600, 700, 800, 900, 1000, 1100 rpm) and check if there
5) Press the Start/Pause button.
6) Press the Signal button repeatedly to set spin speed (600, 700, 800, 900, 1000, 1100 rpm) and check if there
is vibration and noise.
7) If there is no vibration and noise, increase the spin speed by pressing Signal button.
8) If there is vibration and noise, press the Cycle selector button to reduce the Spin Speed (reduce by 50 and 100
8) If there is vibration and noise, press the Cycle selector button to reduce the Spin Speed (reduce by 50 and 100
rpm). In case of 600 rpm, it can not reduce the spin speed.
9) If vibration and noise are reduced, press the WASH/RINSE button to store (2 beep sounds).
* If you want to return to factory default spin speed setting, repeat above steps except step 8).
* If you want to return to factory default spin speed setting, repeat above steps except step 8).
24
NO
YES
NO
NO
YES
NO
YES
YES
NO
NO
YES
YES
YES
NO
NO
NO
YES
SOFTENER
MAX
(4) Main Wash Compartment
4
Is water supply shut-off?
Is the tap opened?
When you press both SPIN SPEED button and
SOIL LEVEL button simultaneously, is the water
level frequency below 246?
SOIL LEVEL button simultaneously, is the water
level frequency below 246?
Is the inlet valve filter clogged?
Is resistance between each terminal of INLET
VALVE ASSEMBLY 0.8-1.2
VALVE ASSEMBLY 0.8-1.2
k
Ω
?
Verify the voltage of the inlet valve connector is
120 V AC.
(Refer to 7-2 QC TEST MODE)
Is water supplied?
Are receptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?
terminals of the INLET VALVE ASSEMBLY?
Has detergent been put in the correct compartment
of the dispenser?
of the dispenser?
Is the detergent caked or hardened?
Open the tap.
Check the AIR CHAMBER
and the tube (clogged).
and the tube (clogged).
Clean the filter.
Replace the INLET VALVE
ASSEMBLY.
ASSEMBLY.
Check electrical connection.
Replace the MAIN PWB
ASSEMBLY.
Replace the MAIN PWB
ASSEMBLY.
Refer to
^NO WATER SUPPLY_
Check the wiring.
Put the detergent in the
correct place.
correct place.
Clean the dispenser.
NO WATER SUPPLY
DETERGENT DOES NOT FLOW IN
Click on the first or last page to see other WM2140CW service manuals if exist.