DOWNLOAD LG WM-12230FB Service Manual ↓ Size: 1.62 MB | Pages: 35 in PDF or view online for FREE

6. WIRING DIAGRAM

/ PROGRAM CHART

 

58

58

57

2:35(2:34)

/Silk

❋ Pre Wash : If the laundry is heavily soiled, “Pre Wash” course is effective. Pre Wash is available in Cotton and Synthetic Program.
❋ Eco : By selecting Eco function, the water temperature is reduced and washing time is lengthened. So you can economize in your

consumption of energy.

❋ Rinse+ : If you wish to rinse more, the Rinse+ function will remove any trace of detergents.
❋ Bio : If you want to eliminate protein stains (milk, blood, chocolate...), you may select Bio function by pressing the option button.
❋ Quick 30 : By selecting this function, you may wash a small quantity of colored laundry which is lightly soiled fast.
❋ You can select Bio function and Eco function when temperature is higher than 60˚C in Cotton and Synthetic. If the function is

selected, the beginning water temperature can not be changed.

※(   ) : WD-80230FB

7-1.BEFORE PERFORMING SERVICE

■ Be careful of electric shock or disconnecting the parts while trouble shooting.
■ Voltage of each terminal in 220-240V and DC while applying an electric current.

7-2.QC TEST MODE.

① Pressing Crease Care, and Pre Wash button simultaneously.
② Power button ON with pressing upper two button. then buzzer sound twice.
③ Press the START/PAUSE button as follows.

~Press the START/PAUSE button more 4 times until stop spinning₩

7-3.HOW TO KNOW THE WATER LEVEL FREQUENCY

Press the Bio and Time delay button simultaneously.

ex) 241 : Water level frequency = 241

× 10-1kHz

=24.1kHz

7. TROUBLESHOOTING

The digits means water level frequency (10

-1 

kHz) 

Pressing number of

［START/PAUSE］button

Checking Point

Display Status

None

All lamps turn on

1 time

Clockwise spin (right)

Motor rpm (About 45)

2 times

Low speed Spin

Motor rpm (About 63~67)

3 times

High speed Spin

Motor rpm (About 79~85) : WD(M)-80230FB

Motor rpm (About 100~106) : WD(M)-10230(5)FB/90230(5)FB

Motor rpm (About 107~103) : WD(M)-11230(5)FB/11230(5)FBB(N)

Motor rpm (About 114~120) : WD(M)-12230(5)FB/WD-12260FB

Motor rpm (About 122~127) : WD(M)-13230(5)FB/13230(5)FBB(N)/WD-13262FB

4 times

Inlet valve for pre-wash operation

Water level frequency (25~65)

5 times

Inlet valve for main-wash operation

Water level frequency (25~65)

Hot inlet valve in case of hot water fill

6 times

Inlet valve for main-wash operation 

Water level frequency (25~65)

7 times

Counterclockwise spin (left)

Motor rpm (About 45)

8 times

A Heater is in operation for 3 sec.

Water Temperature

9 times

Draining pump operation

Water level frequency

10 times

Auto off operation

7-4.ERROR DISPLAY.

If you press the 

~Start/Pause₩button any error except 

will disappear and the machine will change

into pause status.

In case of 

d

e, d

e, d

e, if the error is not resolved within 20 sec. In case of other errors, if the

error is not resolved within 4 min. Power will be turned off automatically and the error only will be
blinked. But in the case of 

d

e, power will not be turned off.

WATER INLET

Water has not reached to the pre-set level within 4 min. since

ERROR

inlet valve operated, or water has not reached to the normal

level within 25 min.

IMBALANCE

The appliance is tilted. 

ERROR

Laundry is gathered to one side.

Non distributable things are put into the drum.

DRAIN ERROR

Water has not drained enough within 5 min.

OVERFLOW

Water is automatically being pumped out because too much

ERROR

water is in the tub.

SENSOR PRESSURE

The sensor pressure switch is out of order.

S/W ERROR

DOOR OPEN

The 

~Start/Pause₩

button is pressed with the door open.

ERROR

The door switch is out of order.

HEATING

ERROR

The thermistor is out of order.

SENSOR

The connector (5-pin, male, white) in the wire harness is not 

ERROR

connected to the connector (5-pin, female) of hall sensor in 

the MOTOR.

Reconnect or repair the contact in the connector.

• The electric contact between the connectors

(5-pin, male in the wire harness and 5-pin, female in the hall sensor) is bad

or unstable.

Reconnect or repair the contact in the connector

• The connector (6-pin, male, natural) in the wire harness is not connected to

the connector (6-pin, female, natural) of PWB ASSEMBLY (Main) or the

electric contact of connectors is bad/unstable.

Reconnect or repair the contact in the connector 

• The electric contact between the connectors 

~6-pin, male, in the wire

harness and 6-pin, female in the controller (Main)

₩is bad or unstable.

Reconnect or repair the contact in the connector

• The Wire Harness between hall sensor in the MOTOR and PWB

ASSEMBLY (Main) is cut (open circuited).

Repair/replace the damaged WIRE HARNESS

• The hall sensor is out of order/defective.

Replace the motor

• The controller (Main) is out of order/defective.

Replace the PWB ASSEMBLY (Main)

• PWB ASSEMBLY (Main) is out of order

Replace the PWB ASSEMBLY (Main)

• Winding in the MOTOR is short-circuited.

Replace the MOTOR

• The Connector (3-pin, male, white) in the wire harness is not connected to

the Connector (3-pin, female, white) of MOTOR.

Reconnect or repair the connector

• The electric contact between the connectors 

~3-pin, male, white in the wire

harness and 6-pin, female, white in the PWB ASSEMBLY (Main)

₩is bad or

unstable.

Reconnect or repair the contact in the connector

• The wire harness between the MOTOR and PWB ASSEMBLY (Main) is cut

(open circuited).

Repair the damaged (open-circuited) WIRE HARNESS

• The hall sensor is out of order/defective.

Replace the PWB ASSEMBLY (Main)

SENSOR

ERROR

CURRENT

ERROR

LOCK

ERROR