DOWNLOAD LG WM-1175FHB Service Manual ↓ Size: 2.59 MB | Pages: 40 in PDF or view online for FREE

Before servicing ask the customer what the trouble is.
Check the adjustment (power supply is 220-240V, remove the transit bolts....)
Check the troubles referring to the troubleshooting.
Decide service steps referring to disassembly instructions.
Then, service and repair.

After servicing, operate the appliance to see whether it works O K  or NOT.

STANDARD INSTALLATION

The appliance should be installed as follows.

Remove the transit bolts

Turn the adjustable feet to

(4EA: ) with supplied wrench. 

set the appliance horizontally.

Keep the transit bolts and  

wrench for future use.

Insert the 4 caps provided 

into the hole.

The appliance goes up by 

rotating the feet clockwise. 

The appliance comes down by

rotating the feet counter-

clockwise.

4. INSTALLATION 

1

REMOVE 

THE TRANSIT BOLTS  

INSTALL THE  APPLIANCE ON

FLAT AND FIRM SURFACE

ADJUST THE 

HORIZONTAL

HOW TO CONNECT INLET HOSE

Check that the rubber washer is inside of the

valve connector.

Connect the inlet hose firmly to prevent leak.

CONNECT DRAIN HOSE

CONNECT POWER PLUG

Make sure that the hose is not twisted.

The drain hose should be placed under 100cm from the floor.

Connect the power plug to the wall outlet.

Avoid connecting several electric devices, 

It may be the cause  of a fire.

Avoid submerging the end of the hose.

TEST OPERATION

Connect the power plug to

In case of Coloureds program.      

the outlet.

Connect the inlet hose.   

Preparation for 

Press the power button.

Press the Start/Pause

washing.

button.

Press the button TEMP

Check if the drum rotates  

Check if water is supplied

and  the present temperature  

clockwise and    

through the detergent 

will be displayed.

counterclockwise. 

dispenser. 

Power off and  then power on.
Check if the door can be 
opened after door lock lamp

turns off.

Turn off Spin and Temp after
pressing the Start/Pause button
and start the machine again.
Check drain and Spin.

If SVC is needed during check,
remove the remaining water by
pulling out the hose cap.

Check the water heating.

Check automatic reverse

Check the water supply.

turn.

Check drain and spin 

Power off and open the 

Water removal 

door

5. OPERATION

2

Press the button to select water temperature.
The water temperature 

[40 C 

50 C

60 C 

Cold

30 C] can be

selected in Coloreds, or Synthetic. 

95 C  is selected for Whites only.
By pressing the button while operating the washer, 
the present temperature is displayed.

If you desire to leave fabrics in the machine without spinning after rinse to
prevent them wrinkling, you may select rinse hold by pressing the spin
button.
If you want to drain and spin, when Rinse Hold function is proceed, Press
the Start/Pause button to cancel the Rinse Hold function and select spin
speed or program. Press the Start/Pause button again to start program.
If you want to drain only, select the no spin or pump program.
If lamp turns on, that function has been selected.

If you want to elimenate protein
stains(milk, blood, chocolate...),
you may select Bio by pressing
the option button.
[You can select Bio when
temperature is higher than 60 C
in Whites, Coloureds and
Synthetic.]

If you wish to rinse more, the
Rinse+ option will remove any
trace of detergents.

By selecting Eco, the water
temperature is reduced and
washing time is lengthened. 
So you can economize in your
consumption of energy.
[You can select Eco when
temperature is higher than 60 C
in Whites, Coloureds and
Synthetic.]

If the laundry is heavily soiled,
“Pre Wash” course is effective.
Pre Wash is available in
Coloureds, Whites and Synthetic
Program.

Child Lock system can be set and canceled by pressing
both [Temp.] and [Time Delay ] button simultaneously.
Once Child Lock is set, all button are inoperable. 
Child Lock system can be set anytime even during
Power-off and operation.
It is automatically cancelled when an operational error
occur.