LG WFT65A36EFT Service Manual ▷ View online
3
1. SPECIFICATIONS
Model
Power Sourse
Input
Capacity
Inner Tub
Inlet W ater
Pressure
Spin Speed
Dim.
Weight
Program
Water Level
Reservation
Unbalance
Switch
Lid Interlock
Switch
Child Lock
Lint Filter
Softener
Dispenser
Detergent
Dispenser
Bleach Inlet
Auto Power
Off
Refer to rating label on the back of W
asher
Refer to rating label on the back of Washer
Refer to rating label on the back of Washer
Plastic / Stainless
0.3kgf/cm
2
~ 8kgf/cm
2
50Hz : 710
50
60Hz : 740
50
Refer to rating label on the back of Washer
Refer to rating label on the back of Washer
Fuzzy(Normal),Quick Wash,Jean,Wool
4 Stages
Available for 3 ~ 48 Hr
B.P Sensor
Magnet Sensor
Applied
Single
Applied
Applied
Applied
Applied
WFT(R,N,F,C,S)65A35(6,7)D(E)P(H,C,D,E,F) Series
/ WFT65A37EET/ WFT65A37EFT / WF65A36EET
4
2-1. HOW TO ADJUST LEVEL
2. INSTALLATION INSTRUCTIONS
1
2
Improper installation of the washer may cause noise and malfunctioning.
1. The ventilating openings in the base area must not be obstructed be
carpeting when the washing machine is installed on a carpeted floor.
2. Install the washing machine on a level and firm surface, any tilt should
be less than 1° .
Installation area
• Install the washer on flat and firm
surface.
Checking level
• Open the lid, and check if the
washer is correctly leveled by
looking down from the top.
looking down from the top.
How to use the adjusting plates
• Use the adjusting plates to level the washer
when the adjustable legs cannot cover the gap.
Turn the adjustable legs to set the
washer horizontal (2 EA).
washer horizontal (2 EA).
Adjustable leg
5
Confirming level
• Place the washer to original position
and confirm the level.
Checking slope
• If installation surface is tilted, the
washer will be shaken.
Horizontal setting
• Lift up the front of the washer and
adjust level by turning the
adjustable legs clockwise or using
the adjusting plate.
adjustable legs clockwise or using
the adjusting plate.
Distance between drain hose and the wall
• Distance between drain hose and the wall should
be more than 10 cm, and the distance between the
other part and the wall should be more than 2 cm.
other part and the wall should be more than 2 cm.
More than 2cm
More than 10cm
More than 2cm
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting Water Supply Hose to water tap, check your hose type
and choose correct instruction. Water Supply Hose may vary according to
the country.
Make sure connect blue inlet hose to cold water tab, and orange inlet hose
to hot water tab.
Connecting Water Supply Hose to water tap
Rubber packing
Water supply hose
Connector
Untighten the screw
Untighten the screw of the connector so
that the tap can be placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
Attach the water supply hose to the connector
Push the water supply hose vertically
upwards so that the rubber seal within the
hose can adhere completely to the tap.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1
Fixing the connector of connector and water supply hose
Attach the water supply hose to the
connector and then tighten it by screwing it
to the right.
Normal Type
Normal tab without thread & screw type inlet hose.)
1
2
3
4
5