DOWNLOAD LG WFS2018EKD Service Manual ↓ Size: 5.41 MB | Pages: 56 in PDF or view online for FREE

Push the water supply hose up so that the rubber
packing within the hose can adhere completely to
the tap.

Connect the water supply hose to the tap and then tighten
it by screwing it to the right.

After connecting the hose, open the tap to
check for any water leakage.

• Connect the water supply hose to intel valve

of the washing machine, and then lock it by
turning the hose connecting part.

• Check to see if there is a rubber seal inside

the connector.

For the cold water (1valve) model, Do not connect to the hot water supply.
It will damage your clothes.

• Connect the drain hose to the

outlet of the drain pump located at
the rear of the washing machine.
Attach the clip to the drain hose.

• And then push it toward the body of

the washing machine as indicated
by the arrow.

• Check that the drain hose is hung

up over the edge of the laundry tub.

• Do not use an extension hose.

•The drain hose should always be properly secured to the drain or standpipe.Failure to secure

the drain hose properly can result in flooding and property damage.

• The end of the drain hose should be placed 39""(99 cm)above the floor.
• The drain must be installed in accordance with any applicable local codes and regulations..
• Make sure that the water lines are not stretched,,pinched,crushed,or kinked.
• Do not insert the drain hose more than 12 ” ((30 cm)into the drain pipe to avoid siphoning and

odor build-up.

• The washer should never be installed or stored in a location subject to freezing temperatures..If the

washer was exposed to freezing temperatures prior to installation,allow it to stand at room
temperature for several hours before use.Damage to the water lines and internal mechanisms of
the washer can result.

• Water supply pressure must be between 14.5 psi and 116 psi ((100 ~800kPa)If the water supply

pressure is more than 116 psi,a pressure reducing valve must be installed.If you have
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that water temperature and water pressure remain within the safe limits.Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure.Failure to do
so can result in damage to the machine.

• Plug the power cord of washer into a properly grounded outlet..Failure to do this can result in shock

or serious injury.

35" ~ 47" ( 0.9~ 1.2m)

Cable Tie

Cable Tie

35" ~ 47" ( 0.9~ 1.2m)

WATER
SUPPLY HOSE
Make sure the
water does not
leak.

POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.

DRAIN HOSE
for pump model
Check if the drain
hose is hung up
before operating the
washing machine.

START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.

ADJUSTABLE LEGS
Use to level the washing
machine for correct
balance & spin
operation.

DRAIN HOSE
for non pump
model

Do not wash fabrics containing flammable materials 
(waxes, cleaning fluids, etc.).

Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size
accordingly. Loosely load clothes no higher than the top row of holes in
the washer tub. To add items after washer has started, press START
button and submerge additional items. Close the lid and press START
button again to restart.

Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily.

Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle,

it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.

Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will
prevent tangling during washing. Fasten zippers, hook, and strings to make sure that these items
don't snag on other clothes.

Nylon net is not supplied by LG.

* Look for a care label on your clothes. This will tell you about the fabric content of your garment 

and how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.

To get the best results, different fabrics need to be washed in different ways. 

• SOIL (Heavy, Normal, Light) 

Separate clothes according to the type and  amount of soil.

• COLOR (Whites, Lights, Darks)

Separate white fabrics from colored fabrics.

• LINT (Lint producers, Collectors)

Separate lint producers and lint collectors. 

Lint Producers  

Terry cloth, Chenile, Towels, Nappies, Diapers

Lint Collectors 

Synthetics, Corduroy, Permanent Press, Socks

• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches, pens, coins,

and keys can damage both your washer and your clothes. 

• Mend any torn garments or loose buttons. Tears or holes may become larger during washing. 
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water. 
• Check the washing instructions.
• Remove tissue in pockets.

• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer. 

Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.

• Use a pretreat soil and stain remover.

Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove. 

Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type
of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.

WIRE