LG WFS2018EKD Service Manual ▷ View online
Note
7
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
One Touch Type
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
1
Fixing Connectors to the Tap
Push the upper connector up till the rubber packing is in tight
contact with the tap.
Then tighten the 4 screws.
contact with the tap.
Then tighten the 4 screws.
3
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors.
Tighten the connectors by holding one connector
and twist middle connector to the right.
and Middle Connectors.
Tighten the connectors by holding one connector
and twist middle connector to the right.
4
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to
the middle connector.
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to
the middle connector.
5
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and start
again from step 1.
If you skip step1, it may cause water leakage.
check for any water leakage.
In case of water leakage, close the tap and start
again from step 1.
If you skip step1, it may cause water leakage.
6
Conector
Medio
Medio
Etiqueta Fija
Manija de Presión
Barra de Presión
Manguera de Suministro de Agua
Empaque de Caucho
Tornillo
Etiqueta Fija
Empaque de Caucho
Placa Guía
Conector
Conector
Etiqueta Fijada
Conector
Medio
Medio
Conector
Medio
Medio
Conector
Manguera de Suministro de Agua
Barra de Presión
Mani
j
a de Presión
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the tap can
be placed in the middle.
be placed in the middle.
In case the tap is large.
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
open the 4 screw and take out the guide
plate and follow step 1.
2
Fixed Stiicker
Pressing Handle
Pressing Handle
Pressing Rod
Water Supply Hose
Middle connector
Rubber packing
Screw
Screw
Fixed sticker
Guide plate
Connector
Connector
Rubber packing
Connector
Middle
Connector
Middle
Connector
Pressing handle
Middle
Connector
Connector
Fixed sticker
Pressing rod
Water Supply Hose
8
Caution
1
Attach the water supply hose to the tap.
Screw Type
Push the water supply hose up so that the rubber
packing within the hose can adhere completely to
the tap.
packing within the hose can adhere completely to
the tap.
2
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then tighten
it by screwing it to the right.
it by screwing it to the right.
3
Check water leakage.
Connecting Water Supply Hose to the machine
After connecting the hose, open the tap to
check for any water leakage.
check for any water leakage.
• Connect the water supply hose to intel valve
of the washing machine, and then lock it by
turning the hose connecting part.
turning the hose connecting part.
• Check to see if there is a rubber seal inside
the connector.
For the cold water (1valve) model, Do not connect to the hot water supply.
It will damage your clothes.
It will damage your clothes.
9
2-3. CONNECT THE DRAIN HOSE
• Connect the drain hose to the
outlet of the drain pump located at
the rear of the washing machine.
Attach the clip to the drain hose.
the rear of the washing machine.
Attach the clip to the drain hose.
• And then push it toward the body of
the washing machine as indicated
by the arrow.
by the arrow.
• Check that the drain hose is hung
up over the edge of the laundry tub.
• Do not use an extension hose.
•The drain hose should always be properly secured to the drain or standpipe.Failure to secure
the drain hose properly can result in flooding and property damage.
• The end of the drain hose should be placed 39""(99 cm)above the floor.
• The drain must be installed in accordance with any applicable local codes and regulations..
• Make sure that the water lines are not stretched,,pinched,crushed,or kinked.
• Do not insert the drain hose more than 12 ” ((30 cm)into the drain pipe to avoid siphoning and
• The drain must be installed in accordance with any applicable local codes and regulations..
• Make sure that the water lines are not stretched,,pinched,crushed,or kinked.
• Do not insert the drain hose more than 12 ” ((30 cm)into the drain pipe to avoid siphoning and
odor build-up.
NOTE :
WARNING
• The washer should never be installed or stored in a location subject to freezing temperatures..If the
washer was exposed to freezing temperatures prior to installation,allow it to stand at room
temperature for several hours before use.Damage to the water lines and internal mechanisms of
the washer can result.
temperature for several hours before use.Damage to the water lines and internal mechanisms of
the washer can result.
• Water supply pressure must be between 14.5 psi and 116 psi ((100 ~800kPa)If the water supply
pressure is more than 116 psi,a pressure reducing valve must be installed.If you have
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that water temperature and water pressure remain within the safe limits.Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure.Failure to do
so can result in damage to the machine.
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that water temperature and water pressure remain within the safe limits.Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure.Failure to do
so can result in damage to the machine.
• Plug the power cord of washer into a properly grounded outlet..Failure to do this can result in shock
or serious injury.
35" ~ 47" ( 0.9~ 1.2m)
Cable Tie
Cable Tie
35" ~ 47" ( 0.9~ 1.2m)
10
3. OPERATING INSTRUCTION
3-1. IDENTIFICATION OF PARTS
POWDER AND LIQUID
DETERGENT BOX
DETERGENT BOX
WATER
SUPPLY HOSE
Make sure the
water does not
leak.
SUPPLY HOSE
Make sure the
water does not
leak.
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
Multi Clean Filter
DRAIN HOSE
for pump model
Check if the drain
hose is hung up
before operating the
washing machine.
for pump model
Check if the drain
hose is hung up
before operating the
washing machine.
BASE
FUNCTION
SELECTOR
SELECTOR
TUB
START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.
BUTTON
Use to start or
stop the washing
machine
temporarily.
ADJUSTABLE LEGS
Use to level the washing
machine for correct
balance & spin
operation.
Use to level the washing
machine for correct
balance & spin
operation.
DRAIN HOSE
for non pump
model
for non pump
model
BODY
Click on the first or last page to see other WFS2018EKD service manuals if exist.