LG WFS1939EKD Service Manual ▷ View online
3
1. SPECIFICATIONS
POWER SOURSE
Refer to rating label on the back of Washer
INPUT
Refer to rating label on the back of Washer
CAPACITY
Refer to rating label on the back of Washer
INNER TUB
Stainless
INLET WATER
PRESSURE
0.3kgf/cm
2
~ 8.0kgf/cm
2
SPIN SPEED
950 rpm
DIM.
Refer to rating label on the back of Washer
WEIGHT
Refer to rating label on the back of Washer
PROGRAM
NOMAL, STAINCARE, ALLERGY CARE, SMART RINSE,
ECO WASH, QUICK WASH, DELICATE, TOWELS, DUVET,
SILENT, TUB CLEAN, FAVORITE, SCHOOL CARE
WATER LEVEL
10 Stages
RESERVATION
Available for 3~18 Hr
UNBALANCE
SWITCH
B.P Sensor
LID INTERLOCK
SWITCH
Magnet Sensor
CHILD LOCK
Applied
SOFTENER
DISPENSER
Applied
DETERGENT
DISPENSER
Applied
BLEACH INILET
Applied
AUTO POWER OFF
Applied
Smart RinseTM
with Jet Spray
Applied
Heater
Applied
* Program can be different according to the model.
4
1
2
Adjustable leg
2-1. HOW TO ADJUST LEVEL
2. INSTALLATION INSTRUCTIONS
Installation area
•
Install the washer on flat and firm
surface.
Checking level
•
Open the lid, and check if the
washer is correctly leveled by
looking down from the top.
How to use the adjusting plates
•
Use the adjusting plates to level the
washer when the adjustable legs cannot
cover the gap.
Turn the adjustable legs to set the
washer horizontal (2 EA).
Improper installation of the washer may cause noise and malfunctioning.
1. The ventilating openings in the base area must not be obstructed be
carpeting when the washing machine is installed on a carpeted floor.
2. Install the washing machine on a level and firm surface, any tilt should
be less than 1° .
5
More than 2cm
More than 10cm
More than 2cm
Checking slope
•
If installation surface is tilted, the
washer will be shaken.
Confirming level
• Place the washer to original position
and confirm the level.
Horizontal setting
•
Lift up the front of the washer and
adjust level by turning the
adjustable legs clockwise or using
the adjusting plate.
Distance between drain hose and the wall
•
Distance between drain hose and the wall should
be more than 10 cm, and the distance between the
other part and the wall should be more than 2 cm.
6
2-2. CONNECTING WATER SUPPLY HOSE
Before connecting Water Supply Hose to water tap, check your hose type and choose correct
instruction. Water Supply Hose may vary according to the country.
Make sure connect blue inlet hose to COLD water tab, and orange inlet hose to HOT water tab.
Rubber packing
Connector
Water supply hose
Normal Type
(Normal tab without thread & screw type inlet hose.)
Connecting Water Supply Hose to water tap
1
2
3
4
5
Untighten the screw
Untighten the screw of the connector so that the tap can be
Untighten the screw of the connector so that the tap can be
placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the rubber packing is in tight
Push the upper connector up till the rubber packing is in tight
contact with the tap. Then tighten the 4 screws.
Attach the water supply hose to the connector
Push the water supply hose vertically upwards so that the rubber
Push the water supply hose vertically upwards so that the rubber
seal within the hose can adhere completely to the tap.
Fixing the connector of connector and water supply hose
Attach the water supply hose to the connector
Attach the water supply hose to the connector
and then tighten it by screwing it to the right.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to check for any water leakage.
After connecting the hose, open the tap to check for any water leakage.
In case of water leakage, close the tap and start again from step 1.