LG WFS1258ETD Service Manual ▷ View online
40
4-8. TROUBLE SHOOTING METHODS ACCORDING TO ERROR MESSAGE
4-8-1. SAFETY CAUTION
-
4-8-
-
2. ERROR MODE SUMMERY
• If you press the START/PAUSE button when an error is displayed, any error except will disappear and
the machine will go into the pause status.
• In case of , if the error is not resolved within 20 seconds, or the in case of other errors, if the
error is not resolved within 4 minutes, power will be turned off automatically and the error code will blink. But in
the case of , power will not be turned off.
• Clutch Motor defect
CLUTCH ERROR
7
• Door not all the way closed.
DOOR OPEN
ERROR
6
• The PRESSURE SENSOR ASSEMBLY is out of
order.
• When water level frequency maintain condition of below 10 kHz
and over 30 kHz
PRESSURE
SENSOR
ERROR
5
• Water is overflowing
(water level frequency is over 21.3kHz).
If FE is displayed, the drain pump will
operate to drain the water automatically.
OVERFLOW
ERROR
4
• Not fully drained within 10 minutes.
DRAIN ERROR
3
• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.
UNBALANCE
ERROR
2
• Correct water level (24.6kHz) is not reached within 8
minutes after water is supplied or it does not
reach the preset water level within 25 minutes.
WATER INLET
ERROR
1
CAUSE
SYMPTOM
ERROR
• Clutch Motor defect
CLUTCH ERROR
7
• Door not all the way closed.
DOOR OPEN
ERROR
6
• The PRESSURE SENSOR ASSEMBLY is out of
order.
• When water level frequency maintain condition of below 10 kHz
and over 30 kHz
PRESSURE
SENSOR
ERROR
5
• Water is overflowing
(water level frequency is over 21.3kHz).
If FE is displayed, the drain pump will
operate to drain the water automatically.
OVERFLOW
ERROR
4
• Not fully drained within 10 minutes.
DRAIN ERROR
3
• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.
UNBALANCE
ERROR
2
• Correct water level (24.6kHz) is not reached within 8
minutes after water is supplied or it does not
reach the preset water level within 25 minutes.
WATER INLET
ERROR
1
CAUSE
SYMPTOM
ERROR
غ There’s built-in AC 120V and DC power in output terminal of PWB assembly in common. Be careful electric
shock when disconnecting parts while trouble shooting. (Wear Electro Static Discharge gloves when working.)
غ After cutting off the power when changing PWB assembly, disconnect or assemble.
غ Be careful static when handling PWB assembly, and use Electro Static Discharge plastic pack
غ Be careful static when handling PWB assembly, and use Electro Static Discharge plastic pack
when delivering or keeping it.
41
4-8. TROUBLE SHOOTING METHODS ACCORIDNG TO ERROR MESSAGE
• The connector (3-pin, male, white) in the MOTOR HARNESS is not
connected to the connector(3-pin, female, white) of STATOR
ASSEMBLY.
• The electric contact between the connectors (3-pin, male, white) in
the MOTOR HARNESS and 4-pin, female, white connector in the
MAIN PWB ASSEMBLY is bad or unstable.
• The MOTOR HARNESS between the STATOR ASSEMBLY and
MAIN PWB ASSEMBLY is cut (open circuited).
• The hall sensor is out of order/defective.
LOCKED
MOTOR
ERROR
8
CAUSE
SYMPTOM
ERROR
• The connector (3-pin, male, white) in the MOTOR HARNESS is not
connected to the connector(3-pin, female, white) of STATOR
ASSEMBLY.
• The electric contact between the connectors (3-pin, male, white) in
the MOTOR HARNESS and 4-pin, female, white connector in the
MAIN PWB ASSEMBLY is bad or unstable.
• The MOTOR HARNESS between the STATOR ASSEMBLY and
MAIN PWB ASSEMBLY is cut (open circuited).
• The hall sensor is out of order/defective.
LOCKED
MOTOR
ERROR
8
CAUSE
SYMPTOM
ERROR
4 2
4-9 TROUBLESHOOTING SUMMARY
`
oGz
~oGGwXGaGo
wYGaGoG
wZGaGnuk
w[GaGR
~oGGwXGaGo
wYGaGoG
wZGaGnuk
w[GaGR
pG}
uhwZGaGtG
isZGGwXGaGjG
is[GGwYGaGoG
uhwZGaGtG
isZGGwXGaGjG
is[GGwYGaGoG
w[GaGqG
w\GaGyG
w\GaGyG
w
ju\Gw\GaGkG
XUGwGGaGXYW}G· \L
YUGzGtVwGaGWG¥GX}
ju\Gw\GaGkG
XUGwGGaGXYW}G· \L
YUGzGtVwGaGWG¥GX}
wXGGwY aG
WU_¥XUYȳ
͡Խ
Ίͽ͑ΥΠ͑͵
͡Խ
Έ͑ΥΠ͑ͳͽ
ΖΤΦΝΥ
΅ΖΤΥ͑ΠΚΟΥΤ
͡Խ
͡Խ
ΖΤΦΝΥ
΅ΖΤΥ͑ΠΚΟΥΤ
wG
XWG}
O^PGGO[P
wG
XWG}
O\PGGO[P
}G
XWTX\G}
O_PGGO[P
_TXYȳ
O_PGGO^P
_TXYȳ
O_PGGO\P
y
y
{Gw
XWG}
O^PGGO[P
XWG}
O\PGGO[P
XWTX\G}
O_PGGO[P
_TXYȳ
O_PGGO^P
_TXYȳ
O_PGGO\P
y
y
{Gw
ͦίͦ͢Խ
ΚΟͤ͑ΥΠ͑ΚΟ͢
ͦίͦ͢Խ
ΚΟͣ͑ΥΠ͑ΚΟͤ
ͦίͦ͢Խ
ΚΟ͑͢ΥΠ͑ΚΟͣ
ΖΤΦΝΥ
΅ΖΤΥ͑ΠΚΟΥΤ
ͦίͦ͢Խ
ΚΟͤ͑ΥΠ͑ΚΟ͢
ͦίͦ͢Խ
ΚΟͣ͑ΥΠ͑ΚΟͤ
ͦίͦ͢Խ
ΚΟ͑͢ΥΠ͑ΚΟͣ
ΖΤΦΝΥ
΅ΖΤΥ͑ΠΚΟΥΤ
`
4 3
4-9-1. TROUBLESHOOTING WITH ERROR
Is displayed?
When you press both Water
level button and Spin button
simultaneously,
is the water level frequency
below 26.0 kHz?
level button and Spin button
simultaneously,
is the water level frequency
below 26.0 kHz?
Check the AIR
CHAMBER
and the tube
(clogged).
CHAMBER
and the tube
(clogged).
Is filter inlet valve clogged
with foreign material?
Is resistance between
each terminal of INLET
VALVE ASSEMBLY
0.8-1.2 k
each terminal of INLET
VALVE ASSEMBLY
0.8-1.2 k
ȳ?
͙ΖΗΖΣ͑ΥΠ͑ͪͦ͑͞ΚΟΝΖΥ͑ΧΒΝΧΖ͑
ΒΤΤΖΞΓΝΪ͚
ΒΤΤΖΞΓΝΪ͚
Replace the
INLET VALVE
ASSEMBLY.
INLET VALVE
ASSEMBLY.
Is the voltage of the inlet
valve connector 12V DC?
( Check the all terminal of
valve connector 12V DC?
( Check the all terminal of
INLET VALVE ASSEMBLY
while the power is on.)
while the power is on.)
Replace the
INLET VALVE
ASSEMBLY
INLET VALVE
ASSEMBLY
ͲΗΥΖΣ͑ΔΙΖΔΜΚΟΘ͑ΔΠΟΟΖΔΥΠΣ͑͝
is the water level frequency
below 24.6 kHz?
is the water level frequency
below 24.6 kHz?
Check the
PRESSURE
SWITCH
PRESSURE
SWITCH
Replace the MAIN PWB
ASSEMBLY
ASSEMBLY
No
Yes
Yes
No
Yes
No
Yes
Yes
No
Yes
No
Yes
No
Yes
ͺΤ͑ͶΝΖΔΥΣΚΔΒΝ͑ΔΠΟΟΖΔΥΚΠΟ͑
ΔΠΣΣΖΔΥͰ
ΔΠΣΣΖΔΥͰ
͙ΖΗΖΣ͑ΥΠ͑ͪͦ͞ΨΚΣΚΟΘ͑ΕΚΒΘΣΒΞ͚
Replace the
MAIN HARNESS
MAIN HARNESS
Yes
No
No
Clean or
replace the filter.
replace the filter.
Is the connector connected to
inlet valve assembly
disconnected or
disassembled?
inlet valve assembly
disconnected or
disassembled?
Reconnect or
repair
the connector
repair
the connector
Is the connector connected to
MAIN PWB assembly dis-
connected or disassembled?
(NA1)
MAIN PWB assembly dis-
connected or disassembled?
(NA1)
Reconnect or
repair
the connector
repair
the connector
[Note] Environmental safety check list
1) No water tap leakage
2) No water tap freeze
3) No entanglement of water supply hose
4) No water shortage
5) No shrinkage on water supply hose due to
1) No water tap leakage
2) No water tap freeze
3) No entanglement of water supply hose
4) No water shortage
5) No shrinkage on water supply hose due to
a possible misuse of hot and cold water
6) No water supply hose leakage
INLET VALVE ERROR
Click on the first or last page to see other WFS1258ETD service manuals if exist.