LG WF-T8510TPT Service Manual ▷ View online
2. INSTALLATION INSTRUCTIONS
2-1. HOW TO ADJUST LEVEL
4
How to use the adjusting plates
¡⁄U se the adjusting plates to level the w asher w hen the
adjustable legs cannot cover the gap.
1
2
Adjustable leg
Turn the adjustable legs to set the w asher
horizontal (2 EA).
Installation area
¡⁄Install the w asher on flat and firm
surface.
Improper installation of the washer may cause noise and malfunctioning.
1. The ventilating openings in the base area must not be obstructed be carpeting
when the washing machine is installed on a carpeted floor.
2. Install the washing machine on a level and firm surface, any tilt should be
less than 1
¡˘
.
CAUTION
Checking level
¡⁄O pen the lid, and check if the w asher is
correctly leveled by looking dow n from
the top.
5
M ore than 10cm
M ore than 2cm
M ore than 2cm
3
5
4
Horizontal setting
¡⁄Lift up the front of the w asher and
adjust level by turning the adjustable
legs clockw ise or using the adjusting
plate.
Confirming level
Distance between drain hose and the wall
Checking slope
¡⁄If installation surface is tilted, the
w asher w ill be shaken.
¡⁄Place the w asher to original position
and confirm the level.
¡⁄D istance betw een drain hose and the w all
should be m ore than 10 cm , and the distance
betw een the other part and the w all should be
m ore than 2 cm .
betw een the other part and the w all should be
m ore than 2 cm .
2-2. CONNECTING WATER SUPPLY HOSE
6
B efore connecti
ng W ater S uppl
y H ose to w ater tap, check your hose type
and choose correct i
nstructi
on. W ater S uppl
y H ose m ay vary accordi
ng to
the country.
M ake sure connect bl
M ake sure connect bl
ue i
nl
et hose to col
d w ater tab, and orange i
nl
et hose
to hot w ater tab.
Connecting Water Supply Hose to water tap
R ubber packing
W ater supply hose
C onnector
Untighten the screw
U ntighten the screw of the connector so
that the tap can be placed in the m iddle.
Fixing the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact w ith the tap. Then
tighten the 4 screw s.
Attach the water supply hose to the connector
Push the w ater supply hose vertically
upw ards so that the rubber seal w ithin the
hose can adhere com pletely to the tap.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to
check for any w ater leakage.
In case of w ater leakage, close the tap and
start again from step 1
Fixing the connector of connector and water supply hose
Attach the w ater supply hose to the
connector and then tighten it by screw ing it
to the right.
N orm al Type
N orm al tab w ithout thread & screw type inlet hose.)
1
2
3
4
5
7
R ubber packing
Screw
Fixed sticker
R ubber packing
G uide plate
C onnector
C onnector
Fixed sticker
M iddle
C onnector
C onnector
M iddle
C onnector
C onnector
W ater Supply H ose
Pressing rod
Pressing handle
C onnector
M iddle
connector
connector
Fixed Stiicker
Pressing H andle
Pressing R od
W ater Supply H ose
Separate Middle connector from Water Supply Hose
Separate M iddle connector from the W ater
Supply H ose by pulling the Pressing R od and
the Pressing H andle that is attached to the
W ater Supply H ose w hile pressing them .
Loosen the fixed nuts to connect the connector to the tap
U ntighten the screw of the connector so that
the tap can be placed in the m iddle.
Fixing Connectors to the Tap
Push the upper connector up till the rubber
packing is in tight contact w ith the tap. Then
tighten the 4 screw s.
Fixing Upper Connector and Middle Connector
R em ove the fixed sticker in betw een the
U pper and M iddle C onnectors. Tighten the
connectors by holding one connector and
tw ist m iddle connector to the right.
Connecting Middle Connector and Water Supply Hose
Press dow n the pressing rod of the W ater
Supply H ose w hich w as separated from
m iddle connector(refer to Step1) and then
join it to the m iddle connector.
One Touch Type
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
open the 4 screw and take out the guide
plate and follow step 1.
In case the tap is large.
Note
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1.
If you skip step1, it may cause water leakage.
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1.
If you skip step1, it may cause water leakage.
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
1
2
3
4
5
6
Click on the first or last page to see other WF-T8510TPT service manuals if exist.