DOWNLOAD LG WF-T8500TPT Service Manual ↓ Size: 4.19 MB | Pages: 55 in PDF or view online for FREE

Model
WF-T8500TPT
Pages
55
Size
4.19 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
wf-t8500tpt.pdf
Date

LG WF-T8500TPT Service Manual ▷ View online

2. INSTALLATION INSTRUCTIONS
2-1. HOW TO ADJUST LEVEL
4
How to use the adjusting plates
¡⁄
Use the adjusting plates to level the washer when the
adjustable legs cannot cover the gap.
1
2
Adjustable leg
Turn the adjustable legs to set the washer 
horizontal (2 EA).
Installation area
¡⁄
Install the washer on flat and firm 
surface.
Improper installation of the washer may cause noise and malfunctioning.
1. The ventilating openings in the base area must not be obstructed be carpeting
when the washing machine is installed on a carpeted floor.
2. Install the washing machine on a level and  firm surface, any tilt should be 
less than 1
¡
¡˘
˘
.
CAUTION
Checking level
¡⁄
Open the lid, and check if the washer is
correctly leveled by looking down from
the top.
5
More than 10cm
More than 2cm
More than 2cm
3
4
Horizontal setting
¡⁄
Lift up the front of the washer and 
adjust level by turning the adjustable 
legs clockwise or using the adjusting
plate.
Confirming level
Distance between drain hose and the wall
Checking slope
¡⁄
If installation surface is tilted, the
washer will be shaken.
¡⁄
Place the washer to original position
and confirm the level.
¡⁄
Distance between drain hose and the wall
should be more than 10 cm, and the distance
between the other part and the wall should be
more than 2 cm.
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting Water Supply Hose to water tap, check your hose type
and choose correct instruction. Water Supply Hose may vary according to
the country.
Make sure connect blue inlet hose to cold water tab, and orange inlet hose
to hot water tab.    
Connecting Water Supply Hose to water tap
Rubber packing
Water supply hose
Connector
Untighten the screw
Untighten the screw of the connector so
that the tap can be placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
Attach the water supply hose to the connector
Push the water supply hose vertically
upwards so that the rubber seal  within the
hose can adhere completely to the tap.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1
Fixing the connector of connector and water supply hose
Attach the water supply hose to the
connector and then tighten it by screwing it
to the right.
Normal Type
Normal tab without thread & screw type inlet hose.)
1
2
3
4
5
7
Rubber packing
Screw
Fixed sticker
Rubber packing
Guide plate
Connector
Connector
Fixed sticker
Middle
Connector
Middle
Connector
Water Supply Hose
Pressing rod
Pressing handle
Connector
Middle
connector
Fixed Stiicker
Pressing Handle
Pressing Rod
Water Supply Hose
Separate Middle connector from Water Supply Hose 
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that
the tap can be placed in the middle.
Fixing Connectors to the Tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the
Upper and Middle Connectors. Tighten the
connectors by holding one connector and
twist middle connector to the right.
Connecting  Middle Connector and Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from
middle connector(refer to Step1) and then
join it to the middle connector.
One Touch Type
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
In case the tap is large.
Note
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1. 
If you skip step1, it may cause water leakage.
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
1
2
3
4
5
6
Page of 55
Display

Click on the first or last page to see other WF-T8500TPT service manuals if exist.