DOWNLOAD LG WF-T8020TD Service Manual ↓ Size: 4.56 MB | Pages: 74 in PDF or view online for FREE

Many washing problems involve poor soil & stain removal, residues of lint and scum,
and fabric damage. For satisfactory washing results, follow these instructions.

• Use correct amount of detergent for load size, amount of soil

and water hardness.

• Use warm or hot water for normal soil.

Different water temperature may be required according to soil

type. 

• Reduce load size.

• Wash with Jean or Soak(Speedy Soak) & Jean wash cycle for

heavy soiled laundry.

• Separate heavily soiled items from lightly soiled ones.

• Pretreat stain and heavy soil according to directions shown on

page 11.

• Rub the stain with bar soap. Wash.

• Do not overfill fabric softener dispenser and do not pour liquid

fabric softener directly onto fabric. 

See page 14 for more instructions.

• Keep the recommendations against Scrud(waxy buildup). (refer

to scrud page14.)

• Use correct amount of detergent for load size, amount of soil

and water hardness.

• To restore discolored load of whites, use rust remover safe for

fabric.

• Install nonprecipitating water softener or an iron filter in your

water supply system for an ongoing problem.

• Before washing, run water for a few minutes to clear lines.
• Wash lint givers eg towels, flannelette sheets, separately from lint

collectors eg synthetic fabrics and remove tissues in pockets

before wash. See page 11 for sorting and caring before loading.

• Do not overload the washer

• Do not overload the washer.

• Some detergents need to be pre-dissolved, check the detergent

instructions. Try pre-dissolving the detergent.

• Increase water temperature using hot water safe for fabric.

• Use proper amount of detergent.

• Never pour chlorine bleach directly on fabric. 

See page 13 for adding liquid bleach.

• Fasten zippers, hooks, and buckles.

• Remove objects in pockets. See page 11 for caring before

loading.

• Do not overload the washer.

Poor soil
removal

• Not enough detergent

• Wash water temperature

too low.

• Overloading the washer

• Incorrect wash cycle

• Incorrect sorting

• Do not pretreat stain

• Undiluted fabric softener

dispensed directly onto

fabric

• A buildup caused by the

interaction of fabric

softener and detergent can

flake off and mark clothes

• Not enough detergent
• Iron or manganese in

water supply, water pipes,

or water heater

• Incorrect sorting

• Tissues left in pocket

• Overloading the washer

• Overloading the washer

• Undissolved detergent

• Use too much detergent

• Incorrect use of chlorine

bleach.

• Unfastened zippers,

hooks, buckles

• Ribs, tears and broken

threads

• Overloading the washer

• Degradation of fabric

Blue Stains

Holes, tears,
or snags

Black or gray
marks on
clothes

Yellow or
brown rust
stains

Lint

Residue or
detergent

For more detailed information for trouble shooting refer to page 46 to 57. 

ERROR DECISION

CAUSE FOR ERROR

BASIS

OCCURRENCE

REMEDY

ERROR

• Water level does not

rise to the set level
in 40 minutes.

• Water is not

completely drained
in 10 minutes.

• Laundry unbalance

during spin.

• In the second QC
Mode the following
message is displayed.

WATER
SUPPLY
& INLET
V/V.

DRAINAGE

UNBALANCE

OVER
FLOODING
ERROR

• Water faucet is closed?
• Water supply is interrupted.

• Inlet V/V is clogged with dirts.
• Connector has bad contact to

the inlet valve.

• Yellow(YL) 2 pin connector has

bad contact to the P.W.B ASM.

• Is the drain hose located

properly?

• Drain hose is not lowered.

• Drain hose is folded or clogged

due to freeze or dirts.

• Bad Drain Motor part or

WHITE(WH) 2 pin connector to
the P.W.B ASM has bad
connection.

• Laundry in the INNER TUB is

filled unevenly.

• Washer is tilted.
• S.F S/W is too closed to the

washing tub, or has bad contact.

• Is the CONNECTOR of Ball

pressure sensor disconnected
or badly tonched?

• Check INLET valve

• Open water faucet.
• Wait until water supply is

resumed.

• Clean or replace filter.
• Correct the connector contact.

• Same as above.

• Hung up drain hose at 0.9~1.3m

high. (For pump)

• Put the hose lower.

(For : Non-pump)

• Unclog the drain hose.

• Replace Drain Motor or correct

the connector contact.

• Try to fill laundry uniformly in the

inner tub.

• Adjust the leg.
• Check and replace S.F S/W.

• Check B.P SENSOR

CONNECTOR  or replace B.P
sensor

ERROR DECISION

CAUSE FOR ERROR

BASIS

OCCURRENCE

REMEDY

ERROR

• LID is opened in the

course of
intermittent spin,
normal spin or
processing
reservation.

• SIGNAL

continuously ringing.

• Water Pressure

Switch is off.

• AUTO OFF relay

S/W is out of order.

• In the second QC

MODE, the following
message is
displayed.

DOOR
OPEN

PRESSURE
SENSOR

AUTO
OFF

LAUNDRY
AMOUNT
SENSOR

• Lid is opened during intermittent

spin or normal spin?

• Lid is opened while processing

reservation?

• Connector to the S.F S/W or

VIOLET(VL) 2 PIN
CONNECTOR to the P.W.B ASM
has bad connection.

• S.F S/W or BALL PRESSURE

SENSOR is bad or bad contact.

• Is placed magnetic in LID-B?

• Connector the Ball Pressure

Sensor(Pressure Switch) or
BLUE(BL) 3 pin connector to
P.W.B ASM has bad connection.

• Ball Pressure Sensor

(Pressure Switch) is bad.
(In the initial state of QC TEST
MODE, the number on the
DISPLAY is less than 63 or
more than 70)

• BLUE(BL) 1pin connector to

P.W.B ASM has bad connection.

• Check MOTOR, CLUTCH, 

V-BELT, CONDENSOR.

• Check over all connectors  if

they have bad connection.

• Closed the lid.

• Closed the lid.

• Correct the connector contact.

• Check and replace S.F S/W or

BALL PRESSURE SENSOR.

• Change the LID-B.

• Correct the connector contact.

• Replace Ball Pressure

Sensor(Pressure Switch).

• Correct the connector contact.
• Change P.W.B ASM.

• Adjust or replace those parts.

• Correct the connectors contact.