LG WF-T8014HN.ABWPBTF Service Manual ▷ View online
37
6) Pulsator doesn’t rotate normally.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
4. Pulsator weakly rotates.
1) Check voltage at the power outlet
where the washer is plugged into.
2) Check capacitance of the
capacitor.
Less than 85%
of rating.
of rating.
Indicating
needle rises and
immediately
indicates
needle rises and
immediately
indicates
stopped after it
The needle
doesn’t move.
doesn’t move.
Lower voltage.
Capacitor is
normal.
normal.
Lack of
capacitance of the
capacitor.
capacitance of the
capacitor.
Capacitor is fully
discharged.
discharged.
Explain the causes and a
transfomer should be
used if necessary.
transfomer should be
used if necessary.
Change the capacitor.
Change the capacitor.
7) Water does not drain.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Drain Hose
1. Check whether the drain hose is put
in a narrow space and blocked
2. Check whether the internal drain
Rubber assembly is bent.
3. Check whether the end of the drain
hose submerged into water or
higher than required.
higher than required.
Bent.
Submerged or
higher than
required.
higher than
required.
Defect of
installation.
installation.
Defect of the drain
rubber asm.
rubber asm.
Defect of
installation.
installation.
Reinstall so that it should
not be blocked by lint
not be blocked by lint
Change the drain rubber
asm.
asm.
Re-install so that it can
be submerged or not
higher than required.
be submerged or not
higher than required.
By lint accumulation.
Blocked
4.Check whether the drain hose is
Blocked by foreign object. It may
Happen in case of the hose is little
Blocked by lint accumulation.
Blocked by foreign object. It may
Happen in case of the hose is little
Blocked by lint accumulation.
Blocked
Blocked hose
Accumulation
Remove the objects and
Reinstall so that it can’t be
Blocked by lint accumulation.
Reinstall so that it can’t be
Blocked by lint accumulation.
38
7) Water does not drain.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
PV Case
1. Check whether the PV asm is
blocked by foreign objects.
Drain Motor
1. Check resistance of the drain
motor if it can not pull the PV link.
Blocked.
Resistance is
normal.
normal.
Drain motor coil is
open.
open.
Contact defect in
connection parts
or defect of the
controller.
connection parts
or defect of the
controller.
Separate the drain motor
from the PV link,
disassemble PV cover
and then remove the
foreign objects within
PV case.
from the PV link,
disassemble PV cover
and then remove the
foreign objects within
PV case.
Check the washer works
normally after repair
and reassembling them.
normally after repair
and reassembling them.
(PV link & drain motor
lever should be
assembled accuratel.)
Change the drain motor
Check the washer
works normally after
reassembling.
(PV link & drain motor
reassembling.
(PV link & drain motor
lever should be
assembled accurately.)
assembled accurately.)
Change the controller if
there is no defects in the
connection parts.
there is no defects in the
connection parts.
39
8) Water drains though it is not the time of drain.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Drain Motor
1. Check whether the drain motor is
normally returned after turning
power off.
(It is considered normal if the lever
of the drain motor is fully pulled out
by the PV spring)
(It is considered normal if the lever
of the drain motor is fully pulled out
by the PV spring)
PV Case
1. If water drains though the drain
motor is normally returned, check
whether PV asm is blocked by
foreign objects or the bellows in
whether PV asm is blocked by
foreign objects or the bellows in
1. Check whether the drain motor or
the drain pump works immediately
after power is turned on.
after power is turned on.
Blocked.
Blocked.
Bellows
deformed.
deformed.
Works.
Defect of the drain
motor.
motor.
Defect of PV
Bellows.
Bellows.
Defect of the
controller(Triac
defect)
controller(Triac
defect)
Change the drain motor.
Remove the objects in
the PV asm.
the PV asm.
Change the PV bellows.
(The bellows may swell
up if it contact petroleum
or petrochemical
substance because it is
made of rubber)
(The bellows may swell
up if it contact petroleum
or petrochemical
substance because it is
made of rubber)
Change the controller.
9) Drain error happens while water drains normally.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Ball Pressure Sensor
1. Check generation frequency of the
Ball Pressure Sensor without water.
Less than
26.3 kHz
26.3 kHz
26.3~27.1 kHz
Defect of the
Ball Pressure
Sensor.
Ball Pressure
Sensor.
Defect of the
controller.
Change the Ball
Pressure Sensor
Pressure Sensor
Change the controller.
Controller
The PV assembly is deformed.
40
10) Spin extraction is not proceeded.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Motor
1. In the case that the wash motor
does not spin during spin extraction;
1) Check there is motor working
sound,or
2) If there is no motor-working
sound;
Check frequency of the
Ball Pressure Sensor, under
no load, or
Is placed the magnetic in
Lid-B.
Lid-B.
Check resistance of the motor.
Drain Motor/Clutch
1. In the case the motor rotates but the
inner tub does not rotates;
1) Check resistance of the drain
motor if the drain motor doesn’t
work,or
work,or
2) Check gap between the PV link
and the brake lever if the inner
tub does not rotates while the
drain motor works.
tub does not rotates while the
drain motor works.
There is motor
working sound.
working sound.
Less than
26.3
26.3
The lid is open.
Defect of magnetic in
LID-B
Contact defect
of the Ball
Pressure Sensor
Pressure Sensor
Resistance is
normal
normal
The clearance is
less than 2.0mm
or more then
3.5mm
The gap is
normal .
(2.0~3.5mm)
less than 2.0mm
or more then
3.5mm
The gap is
normal .
(2.0~3.5mm)
Defect of the
capacitor or
Mechanically
locked.
capacitor or
Mechanically
locked.
Defect of the
Ball Pressure
Sensor.
Ball Pressure
Sensor.
Mistake in use.
Coil is open.
Coil is open.
Defect of
connection part
or defect of the
controller.
Defect of
connection part
or defect of the
controller.
Assembling defect
of the drain motor
or the clutch
of the drain motor
or the clutch
Defect of the
clutch.
clutch.
Change the capacitor
after checking defect of
capacitor.
after checking defect of
capacitor.
check whether the
washing clutch or the
washing tub is blocked
if the motor rotates after
removing the V-belt.
washing clutch or the
washing tub is blocked
if the motor rotates after
removing the V-belt.
Check whether the
motor is locked if the
motor does not rotates
even though the V-belt
being removed.
motor is locked if the
motor does not rotates
even though the V-belt
being removed.
Change the Ball
Pressure Sensor.
Pressure Sensor.
Explain” The lid is close
during operation”
during operation”
Change the Lid-B
Change the Ball
Pressure Sensor.
Pressure Sensor.
Change the motor.
Change the drain motor.
Change the controller
after checking
connection parts.
after checking
connection parts.
Reassemble the drain
motor or the clutch to
keep the clearance.
motor or the clutch to
keep the clearance.
Change the clutch.
Click on the first or last page to see other WF-T8014HN.ABWPBTF service manuals if exist.