LG WF-T7519PR Service Manual ▷ View online
Note
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
One Touch Type
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
1
Fixing Connectors to the Tap
Push the upper connector up till the rubber packing is in tight
contact with the tap.
contact with the tap.
Then tighten the 4 screws.
3
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors.
Tighten the connectors by holding one connector
and twist middle connector to the right.
and Middle Connectors.
Tighten the connectors by holding one connector
and twist middle connector to the right.
4
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to
the middle connector.
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to
the middle connector.
5
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and start
check for any water leakage.
In case of water leakage, close the tap and start
again from step 1.
If you skip step1, it may cause water leakage.
6
Conector
Medio
Etiqueta Fija
Manija de Presi
ón
Barra de Presión
Empaque de Caucho
Tornillo
Etiqueta Fija
Empaque de Caucho
Placa Guía
Conector
Conector
Etiqueta Fijada
Conector
Medio
Conector
Medio
Conector
Barra de Presión
Mania de Presión
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the tap can
be placed in the middle.
be placed in the middle.
In case the tap is large.
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
open the 4 screw and take out the guide
plate and follow step 1.
2
Fixed Stiicker
Pressing Handle
Pressing Handle
Pressing Rod
Water Supply Hose
Middle connector
Rubber packing
Screw
Screw
Fixed sticker
Guide plate
Connector
Connector
Rubber packing
Connector
Middle
Connector
Middle
Connector
Pressing handle
Connector
Fixed sticker
Pressing rod
Water Supply Hose
7
Screw Type
Attach the water supply hose to the tap.
Push the water supply hose up so that the rubber
packing within the hose can adhere completely
to the tap.
packing within the hose can adhere completely
to the tap.
1
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then tighten
it by screwing it to the right.
it by screwing it to the right.
2
Check water leakage.
After connecting the hose, open the faucet to
check for any water leakage.
check for any water leakage.
Connect the water supply hose to inlet valve of
the washing machine, and then lock it by
turning the hose connecting part.
the washing machine, and then lock it by
turning the hose connecting part.
Check to see if there is a rubber seal inside the
connector.
connector.
3
Connecting Water Supply Hose to the machine
Water Supply Hose
Rubber Packing
Water
tap
Hose connector
Rubber seal
8
2-3. CONNECT THE DRAIN HOSE
Connect the drain hose to the outlet of the drain
located at the back side of the washing machine.
located at the back side of the washing machine.
Fix the drain hose with the clip.
And then push it toward the body as in the figure.
And then push it toward the body as in the figure.
Keep it downward while the washing machine is working.
Ensure the hose is free from kinking.
Ensure the hose is free from kinking.
Do not install the washer where it is directly exposed to sunlight,
wind, rain etc.
wind, rain etc.
Plug the power cord of this washer into a properly installed
standard electrical outlet that is switched & earthed.
standard electrical outlet that is switched & earthed.
9
NOTE
"*" Parts can be different according to the model.
"**" LINT FILTER (Only for WF-T7549UP / WF-N7549UR)
"**" LINT FILTER (Only for WF-T7549UP / WF-N7549UR)
WATER SUPPLY
HOSE
BLEACH
DISPENSER
DISPENSER
FUNCTION
SELECTOR
SELECTOR
TUB
BASE
ADJUSTABLE LEGS
DRAIN HOSE
POWER PLUG
START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.
Use to start or
stop the washing
machine
temporarily.
Make sure the
water does not
leak.
water does not
leak.
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
Keep the drain hose
flipped down while
washing is in progress.
flipped down while
washing is in progress.
Use to level the washing
machine for correct
balance & spin
operation.
machine for correct
balance & spin
operation.
MAGIC FILTER /
LINT FILTER
Clean regularly to
stop linting on the
clothes load.
LINT FILTER
Clean regularly to
stop linting on the
clothes load.
POWDER DETERGENT
Box for delayed
washing.
Box for delayed
washing.
(2 adjustable legs are optional, some models have provision for 1 adjustable leg)
CASTORS
Use for easy
translocation
Use for easy
translocation
3. OPERATING INSTRUCTION
3.1. IDENTIFICATION OF PARTS
Click on the first or last page to see other WF-T7519PR service manuals if exist.