DOWNLOAD LG WF-T6016T Service Manual ↓ Size: 3.15 MB | Pages: 56 in PDF or view online for FREE

Model
WF-T6016T
Pages
56
Size
3.15 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
wf-t6016t.pdf
Date

LG WF-T6016T Service Manual ▷ View online

2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting Water Supply Hose to water tap, check your hose type
and choose correct instruction. Water Supply Hose may vary according to
the country.
Make sure connect blue inlet hose to cold water tab, and orange inlet hose
to hot water tab.    
Connecting Water Supply Hose to water tap
Rubber packing
Water supply hose
Connector
Untighten the screw
Untighten the screw of the connector so
that the tap can be placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
Attach the water supply hose to the connector
Push the water supply hose vertically
upwards so that the rubber seal  within the
hose can adhere completely to the tap.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1
Fixing the connector of connector and water supply hose
Attach the water supply hose to the
connector and then tighten it by screwing it
to the right.
Normal Type
Normal tab without thread & screw type inlet hose.)
1
2
3
4
5
7
Rubber packing
Screw
Fixed sticker
Rubber packing
Guide plate
Connector
Connector
Fixed sticker
Middle
Connector
Middle
Connector
Water Supply Hose
Pressing rod
Pressing handle
Connector
Middle
connector
Fixed Stiicker
Pressing Handle
Pressing Rod
Water Supply Hose
Separate Middle connector from Water Supply Hose 
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that
the tap can be placed in the middle.
Fixing Connectors to the Tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the
Upper and Middle Connectors. Tighten the
connectors by holding one connector and
twist middle connector to the right.
Connecting  Middle Connector and Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from
middle connector(refer to Step1) and then
join it to the middle connector.
One Touch Type
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
In case the tap is large.
Note
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1. 
If you skip step1, it may cause water leakage.
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
1
2
3
4
5
6
8
Attach the water supply hose to the tap.
Push the water supply hose up so that the
rubber packing within the hose can adhere
completely to the tap.
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and
then tighten it by screwing it to the right.
Check water leakage.
After connecting the hose, open the faucet to
check for any water leakage.
Connect the water supply hose to inlet valve
of the washing machine, and then lock it by
turning the hose connecting part.
Check to see if there is a rubber seal inside 
the connector.
Screw Type
Water Supply Hose
Rubber Packing
H
Rubber seal
Water
tap
Connecting Water Supply Hose to the machine
1
2
3
9
2-3. CONNECT THE DRAIN HOSE
CAUTION
Hose
Guide
0.9~1.2m
Drain Hose
Within 50mm
Connect the drain hose to 
the outlet of the drain pump
located at the rear of the
washing machine.
Attach the clip to the drain 
hose. And then push it toward
the body of the washing 
machine as indicated by the
arrow.
Check that the drain hose is
hung up over the edge of the
laundry tub.
Do not use an extension hose.
Connect the drain hose to the outlet of the 
drain located at the back side of the
washing machine.
Fix the drain hose with the clip.
And then push it toward the body as in the
figure.
Keep it downward while the washing machine
is working.
Ensure the hose is free from kinking.
Never lay down the drain hose, as water will be discharged.
Be sure the drain hose is properly routed so it will not kink
or lift  from the sink.
The discharge height should be approximately 0.9~1.2m from 
the floor.
Connect the drain hose adjusting the length of it not to be
dropped. If drain hose is dropped the drainage could be poor
because of blockage in the hose.
NOTE
:
Do not install the washer where it is directly exposed to sunlight, wind, rain etc.
Plug the power cord of this washer into a properly installed standard electrical outlet
that is switched & earthed.
For pump model
For non - pump model
Page of 56
Display

Click on the first or last page to see other WF-T6016T service manuals if exist.