LG WF-T1291TP Service Manual ▷ View online
3
1. SPECIFICATIONS
WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3), WF-T802/T852(A)/T853A
WF-T(F/C)1091~3/1191~3T(C/H/P), WF-T(F/C)1022/1122/1001T(C/H/P)
WF-T1268TH/2409KTb/ 2602kTa/T1491TP/T1022THX/T1133TH
WF-T1081TP/T1491TP/T11292TP/T1292TP/T1291TP, LA-1499ST, WF-T1592TP/T1593TP/T1241TP
WF-G15KTB/G13KTC, WF-B15KTB/B13KTC, WF-T1122TPX/T1341TP/T1342TP/T1295TP
Refer to rating label on the back of Washer
Refer to rating label on the back of Washer
Refer to rating label on the back of Washer
Stainless
0.3kgf/cm
2
~ 8kgf/cm
2
250V, 6A for 220~240V/50Hz
125V, 12A for100~127V/60Hz
50Hz : 700
50 / 60Hz : 740
50
Refer to rating label on the back of Washer
Refer to rating label on the back of Washer
Fuzzy, Economy, Jean, Wool
7 Stages
Available for 3 ~ 48 Hr
B.P Sensor (S.F Switch)
B.P Sensor (S.F Switch)
Applied
Double
Applied
Applied
Applied
Applied
Model
Power Sourse
Input
Capacity
Inner Tub
Inlet Water Pressure
Rating of Fuse
Spin Speed
Dim.
Weight
Program
Water Level
Reservation
Unbalance Switch
Lid Interlock Switch
Child Lock
Lint Filter
Softener Dispenser
Detergent Dispenser
Bleach Inlet
Auto Power Off
2. INSTALLATION INSTRUCTIONS
2-1. HOW TO ADJUST LEVEL
4
How to use the adjusting plates
· Use the adjusting plates to level the washer when the
adjustable legs cannot cover the gap.
1
2
Adjustable leg
Turn the adjustable legs to set the washer
horizontal (2 EA).
horizontal (2 EA).
Installation area
·Install the washer on flat and firm
surface.
Improper installation of the washer may cause noise and malfunctioning.
1. The ventilating openings in the base area must not be obstructed be carpeting
when the washing machine is installed on a carpeted floor.
2. Install the washing machine on a level and firm surface, any tilt should be
less than 1
°
°.
CAUTION
Checking level
·Open the lid, and check if the washer is
correctly leveled by looking down from
the top.
the top.
5
More than 10cm
More than 2cm
More than 2cm
3
5
4
Horizontal setting
·Lift up the front of the washer and
adjust level by turning the adjustable
legs clockwise or using the adjusting
plate.
legs clockwise or using the adjusting
plate.
Confirming level
Distance between drain hose and the wall
Checking slope
· If installation surface is tilted, the
washer will be shaken.
· Place the washer to original position
and confirm the level.
· Distance between drain hose and the wall
should be more than 10 cm, and the distance
between the other part and the wall should be
more than 2 cm.
between the other part and the wall should be
more than 2 cm.
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting Water Supply Hose to water tap, check your hose type
and choose correct instruction. Water Supply Hose may vary according to
the country.
Make sure connect blue inlet hose to cold water tab, and orange inlet hose
to hot water tab.
Connecting Water Supply Hose to water tap
Rubber packing
Water supply hose
Connector
Untighten the screw
Untighten the screw of the connector so
that the tap can be placed in the middle.
that the tap can be placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
packing is in tight contact with the tap. Then
tighten the 4 screws.
Attach the water supply hose to the connector
Push the water supply hose vertically
upwards so that the rubber seal within the
hose can adhere completely to the tap.
upwards so that the rubber seal within the
hose can adhere completely to the tap.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1
Fixing the connector of connector and water supply hose
Attach the water supply hose to the
connector and then tighten it by screwing it
to the right.
connector and then tighten it by screwing it
to the right.
Normal Type
Normal tab without thread & screw type inlet hose.)
1
2
3
4
5