LG WF-T1071TP Service Manual ▷ View online
44
10) Spin extraction is not proceeded.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Motor
1. In the case that the wash motor does not
spin during spin extraction;
1) Check there is motor working
sound,or
2) If there is no motor-working
sound;
Check frequency of the
Ball Pressure Sensor
(Pressure Switch), under no load,
or
(Pressure Switch), under no load,
or
Check contact defect of the safety
switch, defect of connection parts
and whether the lid is open if door
error is displayed.
switch, defect of connection parts
and whether the lid is open if door
error is displayed.
Is placed the magnetic in Lid-B.
Check resistance of the motor.
Drain Motor/Clutch
1. In the case the motor rotates but the
inner tub does not rotates;
1) Check resistance of the drain
motor if the drain motor doesn’t
work,or
2) Check gap between the PV link
and the brake lever if the inner
tub does not rotates while the
drain motor works.
tub does not rotates while the
drain motor works.
There is motor
working sound.
working sound.
Less than
26.3
The lid is open
Defect of
connection part.
connection part.
The lid is open.
Defect of magnetic in
LID-B
LID-B
Contact defect of
the Ball Pressure
Sensor(Safety
Switch)
the Ball Pressure
Sensor(Safety
Switch)
Resistance is
normal
normal
The clearance is
less than 2.0mmor
more then 3.5mm
less than 2.0mmor
more then 3.5mm
The gap is normal
(2.0~3.5mm)
(2.0~3.5mm)
Defect of the
capacitor or
Mechanically
capacitor or
Mechanically
locked.
Defect of the
Ball Pressure
Sensor(Pressure
Switch).
Sensor(Pressure
Switch).
Mistake in use.
Mistake in use.
Coil is open.
Coil is open.
Defect of
connection part or
defect of the
controller.
Defect of
connection part or
defect of the
controller.
Assembling defect
of the drain motor or
the clutch
of the drain motor or
the clutch
Defect of the clutch.
Change the capacitor
after checking defect of
capacitor.
check whether the
after checking defect of
capacitor.
check whether the
washing clutch or the
washing tub is blocked
if the motor rotates after
removing the V-belt.
removing the V-belt.
Check whether the
motor is locked if the
motor does not rotates
even though the V-belt
being removed.
motor is locked if the
motor does not rotates
even though the V-belt
being removed.
Change the Ball Pressure
Sensor(Pressure Switch).
Sensor(Pressure Switch).
Explain “The lid is close
during operation”
during operation”
Reconnect the conncetors.
Explain“The lid is close
during operation”
during operation”
Change the Lid-B
Change the Ball Pressure
Sensor(Safety Switch).
Sensor(Safety Switch).
Change the motor.
Change the drain motor.
Change the controller after
checking connection parts.
checking connection parts.
Reassemble the drain
motor or the clutch to
keep the clearance.
motor or the clutch to
keep the clearance.
Change the clutch.
45
11) Spining is going on even though the lid is open.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Safety Switch
1. Check resistance between both
terminals of the safety switch with
the lid open.
the lid open.
Ball Pressure Sensor
1. Is placed the magnetic on the wash?
0~9
Ω
∞Ω
Yes
No
Contact points of
the safety switch
are welded.
the safety switch
are welded.
Defect of the
controller.
controller.
Reed S/W is short
by magnetic on
the washer.
by magnetic on
the washer.
Reed Switch.
Change the Safety
Switch
Switch
Change the controller
Keep magnet away from
the washer.
the washer.
Change the controller.
12) Spin basket doesn’t reach to full speed(normal rpm)
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Main voltage
1. Check voltage at the power outlet
where the washer is plugged into.
Starting Capacitor
1. Check the capacitance of the
starting capacitor.
Clutch Assembling
1. Check the clearance between the
PV link and the brake lever and
clearance between the clutch lever
and the adjustment bolt.
clearance between the clutch lever
and the adjustment bolt.
Blocked by foreign objects
1. Check whether the PV asm, the
drain pump & the drain hose are
blocked by foreign objects so that it
makes water-splashing noise in the
tub.
blocked by foreign objects so that it
makes water-splashing noise in the
tub.
Less than
85% of rating
85% of rating
Lack of
capacitance
capacitance
The clearance is
less than 2.0mm
or more than 3.5mm
less than 2.0mm
or more than 3.5mm
Bolt clearance is
out of range
1.9
out of range
1.9
±
0.1mm
Tool low voltage
Defect of
capacitor
capacitor
Defect of the
clutch
clutch
Explain the cause and
recommend using a
transfomerformer if
necessary.
recommend using a
transfomerformer if
necessary.
Change the capacitor
Adjust PV lever bolt and
paint it red.
Reassemble the drain
motor or the clutch.
paint it red.
Reassemble the drain
motor or the clutch.
Adjust the bolt
clearance.
clearance.
Remove the foreign
objects.
objects.
46
13) Vibration, Noise or Unbalance Error happens during spin.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Using conditions such as
installation etc.
installation etc.
1. Check whether the washer is
leveled. (Check clearance with out
tub and out case the left gap is the
same as the right and the rear gap is
1.5~2 time bigger than the front gap,
same as the right and the rear gap is
1.5~2 time bigger than the front gap,
between the cabinet and the wash
bowl, when it is leveled.)
bowl, when it is leveled.)
2. Check whether laundry in the wash
bowl is out of balance that can
cause severe vibration & noise.
cause severe vibration & noise.
3. Check whether the pulsator doesn’t
rotate during spin.(To check that,
remove the front lid and than run the
spin only cycle.)
remove the front lid and than run the
spin only cycle.)
Safety Switch
1. Check whether the lever of the
safety switch touchs the outer tub if
touching noise happens.
touching noise happens.
Damper
1. Check whether the outer tub cover
hit the top cover without load
during spin.
during spin.
Not leveled.
Laundry is
unbalanced.
The pulsator
rotates initially
then the inner tub
rotates.
rotates initially
then the inner tub
rotates.
The lever is
bented
bented
Hit
Defect of
installation
installation
Defect of the
clutch
Defect of the
safety switch
safety switch
Defect of the
damper
damper
Level the washer.
Explain that it is not out
of order and it may
happen when big & long
laundry is washed.
of order and it may
happen when big & long
laundry is washed.
Change the clutch
spring-B or the clutch
asm.
spring-B or the clutch
asm.
Change the safety
switch.
Don’t repair and reuse it
because it creates
another problem if it is
wrongly repaired.
switch.
Don’t repair and reuse it
because it creates
another problem if it is
wrongly repaired.
Change four dampers
simultaneously.
(In assembling, check
the position to damper
asm)
simultaneously.
(In assembling, check
the position to damper
asm)
It is very important to find out what kinds of noise & where comes from to settle
noise during spin and accumulately service experiance.
47
14) Power is automatically turned off during operation or immediately
turning on the power switch.
Where, what & how to check?
Result of Check
Possible Cause How to repair & settle
Main voltage
1. It is mostly caused by noise from
mains or transfomerient power cut.
mains or transfomerient power cut.
Auto Off switch or
Controller
Controller
1.Check whether power is
automatically turned off when
turning on the auto off switch after
unplugging the power cord from the
outlet
turning on the auto off switch after
unplugging the power cord from the
outlet
2. It would be defect of the controller if
power is automatically turned off
immediately when turning on the
power switch even though there is
no defects in the auto off switch.
immediately when turning on the
power switch even though there is
no defects in the auto off switch.
Automatically
turned off
turned off
Defect in main.
Mechanical defect
of the auto off
switch.
of the auto off
switch.
Explain the cause.
(It happens specially
when a high frequency
equipment is a used
around the washer or in
the case voltage
fluctuation is big)
(It happens specially
when a high frequency
equipment is a used
around the washer or in
the case voltage
fluctuation is big)
Change the auto off
switch.
switch.
Change the controller.
Click on the first or last page to see other WF-T1071TP service manuals if exist.