DOWNLOAD LG WF-SA12HD6 Service Manual ↓ Size: 12.82 MB | Pages: 57 in PDF or view online for FREE

Model
WF-SA12HD6
Pages
57
Size
12.82 MB
Type
PDF
Document
Service Manual
Brand
Device
Washing Machine
File
wf-sa12hd6.pdf
Date

LG WF-SA12HD6 Service Manual ▷ View online

4
1
2
Adjustable leg
2-1. HOW TO ADJUST LEVEL
2. INSTALLATION INSTRUCTIONS
Installation area
•    
Install the washer on flat and firm 
surface.
Checking level
•    
Open the lid, and check if the 
washer is correctly leveled by 
looking down from the top.
How to use the adjusting plates
•    
Use the adjusting plates to level the 
washer when the adjustable legs cannot 
cover the gap.
Turn the adjustable legs to set the
washer horizontal (2 EA).
Improper installation of the washer may cause noise and malfunctioning.
1.  The ventilating openings in the base area must not be obstructed be 
carpeting when the washing machine is installed on a carpeted floor.
2.  Install the washing machine on a level and firm surface, any tilt should  
be less than 1° .
5
More than 2cm
More than 10cm
More than 2cm
Checking slope
•    
If installation surface is tilted, the 
washer will be shaken.
Confirming level
•  Place the washer to original position 
and confirm the level.
Horizontal setting
•    
Lift up the front of the washer and 
adjust level by turning the 
adjustable legs clockwise or using 
the adjusting plate.
Distance between drain hose and the wall
•    
Distance between drain hose and the wall should 
be more than 10 cm, and the distance between the 
other part and the wall should be more than 2 cm.
6
2-2. CONNECTING WATER SUPPLY HOSE
Before connecting Water Supply Hose to water tap, check your hose type and choose correct
instruction. Water Supply Hose may vary according to the country.
Make sure connect blue inlet hose to COLD water tab, and orange inlet hose to HOT water tab.
Rubber packing
Connector
Water supply hose
Normal Type
(Normal tab without thread & screw type inlet hose.)
Connecting Water Supply Hose to water tap
1
2
3
4
5
Untighten the screw
Untighten the screw of the connector so that the tap can be
placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the rubber packing is in tight
contact with the tap. Then tighten the 4 screws.
Attach the water supply hose to the connector
Push the water supply hose vertically upwards so that the rubber
seal within the hose can adhere completely to the tap.
Fixing the connector of connector and water supply hose
Attach the water supply hose to the connector
and then tighten it by screwing it to the right.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to check for any water leakage.
In case of water leakage, close the tap and start again from step 1.
7
Conector
Medio
Etiqueta
Fija
Manija de Presión
Barra de Presión
Manguera de Suministro de Agua
Empaque
de Caucho
Tornillo
Etiqueta
 Fija
Empaque
de Caucho
Placa Guía
Conector
Conector
Etiqueta
Fijada
Conector
Medio
Conector
Medio
Conector
Manguera de Suministro de Agua
Barra de Presión
Mani
ja
 de Presión
Fixed Stiicker
Pressing Handle
Pressing Rod
Water Supply Hose
Middle connector
Rubber packing
Screw
Fixed sticker
Guide plate
Connector
Connector
Rubber packing
Connector
Middle
Connector
Pressing handle
Middle
Connector
Fixed sticker
Pressing rod
Water Supply Hose
One Touch Type
Note
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
1
2
3
4
5
6
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the tap can
be placed in the middle.
Fixing Connectors to the Tap
Push the upper connector up till the rubber packing is in tight
contact with the tap.
Then tighten the 4 screws.
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors.
Tighten the connectors by holding one connector
and twist middle connector to the right.
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to
the middle connector.
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and start
again from step 1.
If you skip step1, it may cause water leakage.
In case the tap is large.
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
Page of 57
Display

LG WF-SA12HD6 Service Manual ▷ Download

  • DOWNLOAD LG WF-SA12HD6 Service Manual ↓ Size: 12.82 MB | Pages: 57 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the LG WF-SA12HD6 in PDF for free, which will help you to disassemble, recover, fix and repair LG WF-SA12HD6 Washing Machine. Information contained in LG WF-SA12HD6 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.