DOWNLOAD LG WF-S6507PPD Service Manual ↓ Size: 3.77 MB | Pages: 64 in PDF or view online for FREE

Remove two back panel fixing screws in the back

side.

Disassemble the back panel.

Disconnect two connectors and disassemble the

power cord.

Remove a valve fixing screw & disconnect the

leads form the inlet valve.

Remove the inlet valve.

Disconnect the leads & the pressure tube from the

BP sensor.

Remove the BP sensor.

Remove Q-spring & two hinge pins then

disassemble the lid assembly

Remove two top cover fixing screws in the rear

then disassemble the top cover.

Remove tub cover fixing screws then disassemble

the tub cover.

Remove the pulsator fixing screw then disassemble

the pulsator.

Remove the hub fixing nut by a special tool.

Disassemble the inner tub.

Inlet valve

Power cord

BP sensor

Q-spring

Hinge Pin

Hinge Pin

Remove back cover fixing screws then
disassemble the back cover.

Disconnect the leads and the drain hose-p from the
drain pump.

Remove the pump fixing screws then disassemble
the drain pump.

Fall down the washer for clutch & motor removal.

Remove the belt.

Disassemble the clutch.

Remove two motor fixing screws then disassemble
the motor.

Separate top cover from washing machine.

As in the fig, lift snubber bar and take it out of out 

case with out tub.

Damper assembly shall not be disassembled.
Replace damper as assembly.

For assembly, keep the following.(Location & color)

Location

P/No.

PIVOT(Color)

,

A051

NATURAL

,

A052

BLUE

A

D

C

B

Pump fixing screw

Leads

Drain hose-p

Pulsator

Tub cover

Inner tub

Hub fixing nut

EX-LARGE

LARGE

MEDIUM

SMALL

8

4

2

1

8

4

2

1

8

4

2

1

FUZZY

ECONOMY

JEAN

WOOL

TURBO(SOAK) , Speedy soak

WASH

RINSE

SPIN

8

4

2

1

EX-LARGE

LARGE

MEDIUM

SMALL

8

4

2

1

8

4

2

1

FUZZY

ECONOMY

JEAN

WOOL

TURBO(SOAK), Speedy soak

WASH

RINSE

SPIN

• To use the CHECK PROGRAM (QC TEST MODE), press PROCESS key, and PROGRAM key at the

same time and then the POWER switch on without depositing any laundry.

NO

CHECK METHOD

LED INDICATOR

CHECK ITEM

1

2

3

4

5

6

7

8

Initial state

Press once

Press twice

Press 3 times

Press 4 times

Press 5 times

Press 6 times

Press 7 times

• After laundry amount detecting,

LED indicates laundry amount
and WATER LEVEL.

• Pump model: MEDIUM water

level Led ON.

• Non-pump model:water level

MEDIUM water level Led OFF.

• All LED on.

• After 2~3 seconds water level

frequency is displayed on LED.

• Laundry amount test.

• After checking laundry amount, motor

is on. (Left & Right)

• Cold water

• Hot water.

• Drain motor is 1st state is play.
• If lid is opened door error display.

(wash and spin LED blinks)

• Drain motor is 2nd state.(Only WF-T Series)

• Drain pump is on.

• AUTO off switch.

• WATER LEVEL FREQUENCY & LAUNDRY AMOUNT ARE DISPLAY BY THE LED (WATER LEVEL,

PROCESS, PROGRAM)

Ex) Water level check ; Frequency : 26.7 KHz

Ex) Laundry amount ; Water level : MEDIUM

Pulse : 25

Many washing problems involve poor soil & stain removal, residues of lint and scum,
and fabric damage. For satisfactory washing results, follow these instructions.

• Use correct amount of detergent for load size, amount of soil

and water hardness.

• Use warm or hot water for normal soil.

Different water temperature may be required according to soil
type. (refer to page 12)

• Reduce load size.
• Wash with Jean or Soak(Turbo) & Jean wash cycle for heavy

soiled laundry.

• Separate heavily soiled items from lightly soiled ones.
• Pretreat stain and heavy soil according to directions shown on

page 11.

• Rub the stain with bar soap. Wash.
• Do not overfill fabric softener dispenser and do not pour liquid

fabric softener directly onto fabric. 
See page 14 for more instructions.

• Keep the recommendations against Scrud(waxy buildup). (refer

to scrud page14.)

• Use correct amount of detergent for load size, amount of soil

and water hardness.

• To restore discolored load of whites, use rust remover safe for

fabric.

• Install nonprecipitating water softener or an iron filter in your

water supply system for an ongoing problem.

• Before washing, run water for a few minutes to clear lines.

• Wash lint givers eg towels, flannelette sheets, separately from lint

collectors eg synthetic fabrics and remove tissues in pockets
before wash. See page 11 for sorting and caring before loading.

• Do not overload the washer

• Do not overload the washer.
• Some detergents need to be pre-dissolved, check the detergent

instructions. Try pre-dissolving the detergent.

• Increase water temperature using hot water safe for fabric.
• Use proper amount of detergent.

• Never pour chlorine bleach directly on fabric. 

See page 13 for adding liquid bleach.

• Fasten zippers, hooks, and buckles.
• Remove objects in pockets. See page 11 for caring before

loading.

• Do not overload the washer.

Poor soil
removal

• Not enough detergent
• Wash water temperature

too low.

• Overloading the washer
• Incorrect wash cycle
• Incorrect sorting
• Do not pretreat stain

• Undiluted fabric softener

dispensed directly onto
fabric

• A buildup caused by the

interaction of fabric
softener and detergent can
flake off and mark clothes

• Not enough detergent

• Iron or manganese in

water supply, water pipes,
or water heater

• Incorrect sorting
• Tissues left in pocket
• Overloading the washer

• Overloading the washer
• Undissolved detergent
• Use too much detergent

• Incorrect use of chlorine

bleach.

• Unfastened zippers,

hooks, buckles

• Ribs, tears and broken

threads

• Overloading the washer
• Degradation of fabric

Blue Stains

Holes, tears,
or snags

Black or gray
marks on
clothes

Yellow or
brown rust
stains

Lint

Residue or
detergent