LG WF-D8525DDD Service Manual ▷ View online
3-5. Safety Reed Switch
●
This reed switch system may differ from the old one. The reed switch is in PC board module
and works through contacting with magnets inside lid switch. It would not work until lid is
closed and current is passed through.\
and works through contacting with magnets inside lid switch. It would not work until lid is
closed and current is passed through.\
● Do not place any magnetic object on the machine, which may lead to operation error.
3-6. Intelligence perception
● Seven intelligence perception including unbalance, measurement, water level, door openness,
water temperature , water hardness and detergent density
● Unbalance perception may differ from that of old models. It percepts unbalance through
motor rotate speed of DD motor sensor under “SPIN” and abnormal operation.
3-7.10 Section level
● 10 section water level
● The water level can be adjusted manually with a cycle of
[7
● The water level can be adjusted manually with a cycle of
[7
→8→9→10→1→2→3→4→5→6→7…] according to requirements as
the button is pressed.
Water
level/detergent
level/detergent
Water level
9
4. Identification of Parts
POWER DETERGENT
AND SOFTNER BOX
FILTER
BLEACH DISPENSER
*FUNCTION SLECTOR
*STAINLESS TUB
START/PAUSE
ADJUSTABLE LEGS
WATER SUPPLY
HOSE
●Make sure the water
does not leak~
POWER PLUG
●
●
If the supply cord
is damaged, it must
be replaced by the
qualified person.
is damaged, it must
be replaced by the
qualified person.
*Holder can be fixable
*DRAIN HOSE
●Check if the drain hose
is hang up before
operating the washing
machine.
10
27
Connecting Water Supply Hose to water tap
Connector
Connector
Water
Supply Hose
Supply Hose
screw
Untighten the screw
Untighten the screw of the connector so that the
tap can be placed in the middle.
tap can be placed in the middle.
Fixing the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
packing is in tight contact with the tap. Then
tighten the 4 screws.
Attach the water supply hose securely to the
connector
connector
Push the water supply hose vertically upwards so
that the rubber seal within the hose can adhere
completely to the tap.
that the rubber seal within the hose can adhere
completely to the tap.
Check the connection of water supply hose and the connector
After connecting the hose, open the tap to check
for any water leakage.
If the water leaks, close the tap and start again
from step 1
for any water leakage.
If the water leaks, close the tap and start again
from step 1
Fixing the connector to the water supply hose
Attach the water supply hose to the connector and
then tighten it by screwing it to the right.
then tighten it by screwing it to the right.
Normal Type
(Normal tap without thread & screw type inlet hose.)
1
2
3
4
5
Rubber packing
NOTE
The washing machine is to be connected to the water mains using new hose-sets and old hose-sets should
not be reused.
not be reused.
5.1 Connecting Water Supply Hose
5.Installation Guide
Rubber packing
Rubber packing
Fixed sticker
screw
Guide plate
Connector
Connector
Fixed sticker
Middle
Connector
Connector
Middle
Connector
Connector
Water Supply Hose
Pressing rod
Pressing handle
Connector
Middle
connector
connector
Fixed Sticker
Pressing Handle
Pressing Handle
Pressing Rod
Water Supply Hose
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
tap can be placed in the middle.
Fixing Connectors to the Tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
packing is in tight contact with the tap. Then
tighten the 4 screws.
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water Supply
Hose which was separated from middle connector
(refer to Step1) and then join it to the middle
connector.
Hose which was separated from middle connector
(refer to Step1) and then join it to the middle
connector.
Normal Type
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate. Then follow step1.
untighten the 4 screws and remove the guide
plate. Then follow step1.
In case tap is too large.
NOTE
Check for water leakage
After connecting the hose, open the tap to check
for any water leakage.
If the connection leaks, close the tap and start
again from step 1.
If you skip step 1, water leakage may occur.
for any water leakage.
If the connection leaks, close the tap and start
again from step 1.
If you skip step 1, water leakage may occur.
(Normal tap without thread & one touch type inlet hose.)
1
2
3
4
5
6
Click on the first or last page to see other WF-D8525DDD service manuals if exist.