DOWNLOAD LG WF-759G Service Manual ↓ Size: 9.1 MB | Pages: 62 in PDF or view online for FREE

EX-LARGE
LARGE
MEDIUM
SMALL

8
4
2
1

8
4
2
1

8
4
2
1

FUZZY
ECONOMY
JEAN
WOOL

TURBO(SOAK) , Speedy soak
WASH
RINSE
SPIN

8
4
2
1

EX-LARGE
LARGE
MEDIUM
SMALL

8
4
2
1

8
4
2
1

FUZZY
ECONOMY
JEAN
WOOL

TURBO(SOAK), Speedy soak
WASH
RINSE
SPIN

• To use the CHECK PROGRAM (QC TEST MODE), press PROCESS key, and PROGRAM key at the

same time and then the POWER switch on without depositing any laundry.

NO CHECK METHOD

LED INDICATOR

CHECK ITEM

1

2

3

4

5

6

7
8

Initial state

Press once

Press twice

Press 3 times

Press 4 times

Press 5 times

Press 6 times
Press 7 times

• After laundry amount detecting,

LED indicates laundry amount

and WATER LEVEL.

• Pump model: MEDIUM water

level Led ON.

• Non-pump model:water level

MEDIUM water level Led OFF.

• All LED on.
• After 2~3 seconds water level

frequency is displayed on LED.

• Laundry amount test.
• After checking laundry amount, motor

is on. (Left & Right)

• Cold water

• Hot water.
• Drain motor is 1st state is play.

• If lid is opened door error display.

(wash and spin LED blinks)

• Drain motor is 2nd state.(Only WF-T Series)

• Drain pump is on.
• AUTO off switch.

• WATER LEVEL FREQUENCY & LAUNDRY AMOUNT ARE DISPLAY BY THE LED (WATER LEVEL,

PROCESS, PROGRAM)

Ex) Water level check ; Frequency : 26.7 KHz

Ex) Laundry amount ; Water level : MEDIUM

Pulse : 25

Many washing problems involve poor soil & stain removal, residues of lint and scum,
and fabric damage. For satisfactory washing results, follow these instructions.

• Use correct amount of detergent for load size, amount of soil

and water hardness.

• Use warm or hot water for normal soil.

Different water temperature may be required according to soil

type. 

• Reduce load size.

• Wash with Jean or Soak(Turbo) & Jean wash cycle for heavy

soiled laundry.

• Separate heavily soiled items from lightly soiled ones.

• Pretreat stain and heavy soil according to directions shown on

page 11.

• Rub the stain with bar soap. Wash.

• Do not overfill fabric softener dispenser and do not pour liquid

fabric softener directly onto fabric. 

See page 14 for more instructions.

• Keep the recommendations against Scrud(waxy buildup). (refer

to scrud page14.)

• Use correct amount of detergent for load size, amount of soil

and water hardness.

• To restore discolored load of whites, use rust remover safe for

fabric.

• Install nonprecipitating water softener or an iron filter in your

water supply system for an ongoing problem.

• Before washing, run water for a few minutes to clear lines.
• Wash lint givers eg towels, flannelette sheets, separately from lint

collectors eg synthetic fabrics and remove tissues in pockets

before wash. See page 11 for sorting and caring before loading.

• Do not overload the washer

• Do not overload the washer.

• Some detergents need to be pre-dissolved, check the detergent

instructions. Try pre-dissolving the detergent.

• Increase water temperature using hot water safe for fabric.

• Use proper amount of detergent.

• Never pour chlorine bleach directly on fabric. 

See page 13 for adding liquid bleach.

• Fasten zippers, hooks, and buckles.

• Remove objects in pockets. See page 11 for caring before

loading.

• Do not overload the washer.

Poor soil
removal

• Not enough detergent

• Wash water temperature

too low.

• Overloading the washer

• Incorrect wash cycle

• Incorrect sorting

• Do not pretreat stain

• Undiluted fabric softener

dispensed directly onto

fabric

• A buildup caused by the

interaction of fabric

softener and detergent can

flake off and mark clothes

• Not enough detergent
• Iron or manganese in

water supply, water pipes,

or water heater

• Incorrect sorting

• Tissues left in pocket

• Overloading the washer

• Overloading the washer

• Undissolved detergent

• Use too much detergent

• Incorrect use of chlorine

bleach.

• Unfastened zippers,

hooks, buckles

• Ribs, tears and broken

threads

• Overloading the washer

• Degradation of fabric

Blue Stains

Holes, tears,
or snags

Black or gray
marks on
clothes

Yellow or
brown rust
stains

Lint

Residue or
detergent

For more detailed information for trouble shooting refer to page 40 to 51. 

ERROR DECISION

CAUSE FOR ERROR

BASIS

OCCURRENCE

REMEDY

ERROR

• Water level does not

rise to the set level

in 40 minutes.

• Wash and rinse 

LED blink.

• Water is not

completely drained

in 10 minutes.

• Rinse and spin 

LED blink.

• Laundry unbalance

during spin.

• Wash, Rinse and

Spin LED blink.

• In the second QC

Mode the following

message is displayed.

• All of process LED

blinks.

• LID is opened in the

course of

intermittent spin,

normal spin or

processing

reservation.

• Wash and Spin 

LED blink.

• SIGNAL

continuously ringing.

• BALL PRESSURE

SENSOR is off.

• All water level 

LED blinks.

• AUTO OFF relay is

out of order.

WATER

SUPPLY

& INLET

VALVE.

DRAINAGE

UNBALANCE

OVER

FLOODING

ERROR

DOOR

OPEN

BALL

PRESSURE

SENSOR

AUTO

OFF

• Water faucet is closed?

• Water supply is interrupted.
• Inlet V/V is clogged with dirts.

• Connector has bad contact to

the inlet valve.

• Yellow(YL) 2 pin connector has

bad contact to the P.W.B ASM.

• Is the drain hose located

properly?

• Drain hose is folded or clogged

due to freeze or dirts.

• Bad Drain Motor part or  2 pin

connector to the P.W.B ASM has

bad connection.

• Laundry in the INNER TUB is

filled unevenly.

• Washer is tilted.

• Is the CONNECTOR of Ball

pressure sensor disconnected

or badly touched?

• Check INLET valve

• Lid is opened during intermittent

spin or normal spin?

• Lid is opened while processing

reservation?

• Is placed magnetic in Lid-B 

• Connector the BALL

PRESSURE SENSOR  or

BLUE(BL) 3 pin connector to

P.W.B ASM has bad connection.

• BALL PRESSURE SENSOR is bad.

(In the initial state of QC TEST

MODE, the number on the

DISPLAY is less than 63 or

more than 70)

• BLUE(BL) 1pin connector to

P.W.B ASM has bad connection.

• Open water faucet.

• Wait until water supply is

resumed.

• Clean or replace filter.

• Correct the connector contact.
• Same as above.

• Put the hose lower.
• Unclog the drain hose.

• Replace Drain Motor or correct

the connector contact.

• Try to fill laundry uniformly in the

inner tub.

• Adjust the leg.

• Check B.P SENSOR

CONNECTOR or replace B.P

sensor

• Closed the lid.
• Closed the lid.
• Change the Lid-B.

• Correct the connector contact.

• Replace BALL PRESSURE

SENSOR.

• Correct the connector contact.

• Change PWB ASM.

Where, what & how to check?

Result of Check Possible Cause

How to repair & settle

1. Check whether connection between

the plug and the electrical is poor

2.  Measure voltage of the electrical.

1. Measure resistance between both 

ends of the power supply cord with 

both the plug pins short-circuited.

2. Check whether every connector in 

the bundle of connectors has a 

good connection.

3. Check resistance of every wire to 

find out a open wire.

1. Check resistance with  power relay 

switch turned on

2. Check the secondary voltage of the 

transfomer.

3. Measure resistance to check 

whether the T.P of the motor is 

blown out.

4. Check whether the fuse is open.

If there are no defects in the above, 
it should be defect of the controller.
If supply voltage is 120% higher than

rating the varistar in the controller may

be broken. Check supply voltage.

Poor

Around rating
0V

Less than 1

Male & female

connectors

separated

Less than 0.5

More than 1.0

10~14V
0V

motor is hot

Open

Over 120%

voltage than 

rating check

Defect of the 

electrical
No defect
Defect of household

power supply

No defect
Open circuit of the

power supply cord

Poor connection.

Wire is opened.

No defect
Poor contact

No defect
Coil is open

T.P blown out

Defect of the fuse

Change the electrical.

Call for power supply 

company

Change the power 

supply cord.

Remove the cause to 

give strain and 

reconnect them.
Change the lead wire.

Change the Auto Off 

Switch

Change the

transfomerformer.

Remove cause to 

overload the motor

Change the fuse.

Check the fuse rating

AC100~127V:125V 12A

AC220~240V:250V   6A

Change the controller

if all the electrical parts 

have no defects.