LG WD6-14129SR Service Manual ▷ View online
29
Power off for 10sec. Then power on.
Is the water level over reference line and is the water level frequency under 21.3kHz?
* Water level frequency
- Touch and Hold '
Pre Wash
' & '
Temp.
'
simultaneously.
FE (Overflow Error)
If FE is displayed again,
then replace the
Pressure Switch
.
If FE is displayed again,
then replace the
Main PCB
.
Drain out the water and then
check the
Air Chamber
and the
Tube
(clogged).
NO
NO
YES
YES
Is water continuously
coming into the drawer?
Replace the
Main PCB.
Replace the
Inlet Valve
assembly.
Data view type: ‘040’
30
Is the air chamber and the tube clogged?
Replace the
Main PCB
.
Is the
Connector
connected correctly to
the
Main PCB
and the
Pressure Switch
?
Is the
Harness
right?
Reconnect or repair the
Connector
.
Or replace the
Harness
.
Check air chamber and remove foreign material.
Replace the
Pressure Switch
.
YES
YES
NO
Is the resistance of the
Pressure Switch
out of range?
[Pin1 ~ Pin3]
21~23Ω)
NO
NO
YES
PE (Pressure Sensor S/W Error)
31
NO
Is the door closed?
Is the Door assembly in line with door switch ?
Lift up & close the door.
If the dE is displayed, replace the
Door Bracket
.
Close the door fully.
Reconnect or repair the
Connector
.
Or replace the
Harness
.
NO
NO
Replace the
Spring.
NO
Replace the
Door switch
.
NO
Does the
Spring
of
Latch Hook
actuate?
dE (Door Open Error)
YES
YES
YES
YES
Scratch by Latch Hook
Touching
or
Is the
Connector
connected correctly to
the
Main PCB
and the
Door Switch
?
Is the
Harness
right?
Does the
Door Switch
operate as follows?
* Door locking time :
1~8
sec.
Check the time from power on
to the time to door locking.
to the time to door locking.
* Door releasing time :
25~100
sec.
Check the time from power off to
door releasing.
door releasing.
32
No
Is the resistance of the
Thermistor
out of range 44 ~
53 KΩ at 25°C? (Page 17)
Replace the
Main PCB
.
Is the
Connector
connected correctly to
the
Main
PCB, the
Thermistor
and the
Heater
?
Is the
Harness
right?
Reconnect or repair the
Connector
.
Or replace the
Harness
.
Replace the
Thermistor
.
YES
Replace the
Heater
.
YES
YES
Is the resistance of the
Heater
out of range 24.5 ~
28.5Ω (for Washing) or 42.5 ~ 49.5Ω (for Steam) ?
(Page 19)
(Page 19)
[Note] Thermistor Spec
NO
NO
tE (Thermistor (Heating) Error)
S
P
E
C
Temp
30 °C
40 °C
60 °C
70 °C
95 °C
105 °C
Resistance (kΩ)
MIN
36.35
39.45
42.72
24.20
26.05
27.97
11.43
12.12
12.82
8.088
8.514
8.940
3.544
3.791
4.045
2.617
2.816
3.023
STD
MAX
Heater for Washing
Heater for Steam
Click on the first or last page to see other WD6-14129SR service manuals if exist.