LG WD-R1028UDS Service Manual ▷ View online
3. PARTS IDENTIFICATION
7
Manguera de entrada (1 EA)
Opción : Caliente/Fría (2 EA)
Llave de tuercas
Accessorios
Enchufe de toma de corriente
Si el cable de alimentación se daña,
debe ser sustituido por el fabricante o
sus representantes de servicio o por
una persona igualmente calificada, con
el fin de evitar cualquier peligro.
debe ser sustituido por el fabricante o
sus representantes de servicio o por
una persona igualmente calificada, con
el fin de evitar cualquier peligro.
Panel de control
Tapón de la cubierta inferior
Puerta
Patas de nivelación
??
Cajón
(Para el detergente
y el suavizante
para tejidos)
y el suavizante
para tejidos)
Manguera
de drenaje
de drenaje
Tambor
Ventilación
de Seguridad
de Seguridad
Entrada de
Agua Caliente
Agua Caliente
Entrada de Agua Fría
Filtro de la bomba de drenaje
Tapón de drenaje
Parte Trasera de la Lavadora
1⃞ Before servicing ask troubles of customers
2⃞ Check the adjustment(power supply is 220-240V ac 50Hz, remove the transit bolts....)
3⃞ Check the troubles referring to the trouble shooting.
4⃞ Decide service steps referring to disassembly instructions.
5⃞ And then, service and repair.
6⃞ After servicing, operate the appliance whether it works O·K or NOT.
2⃞ Check the adjustment(power supply is 220-240V ac 50Hz, remove the transit bolts....)
3⃞ Check the troubles referring to the trouble shooting.
4⃞ Decide service steps referring to disassembly instructions.
5⃞ And then, service and repair.
6⃞ After servicing, operate the appliance whether it works O·K or NOT.
■ STANDARD INSTALLATION
The appliance should be installed as follows.
REMOVE THE TRANSIT
INSTALL THE APPLIANCE
ADJUST THE
BOLTS
ON FLAT AND FIRM SURFACE
LEVELING
Remove the transit bolts
(4EA:
①)with supplied spanner.
Keep the transit bolts and
spanner for future use.
Insert the 4 caps
provided into the hole
4. INSTALLATION
8
1
2
Turn the leveling feet to adjust the
appliance.
Turn clockwise to raise;
counterclockwise to lower.
Favorite
Sanitary
■ HOW TO CONNECT INLET HOSE
Check that the rubber packing is inside of the
valve connector.
Connect the inlet hose firmly to prevent leak.
■ CONNECT DRAIN HOSE
■ CONNECT POWER PLUG
9
· Make sure that the hose is not twisted.
※ The drain hose should be placed under 100cm from the floor.
· Connect the power plug to the wall outlet.
· Avoid connecting several electric devices,
It may be the cause of the fire.
· Avoid submerging the end of the hose.
Favorite
Sanitary
Favorite
Sanitary
Favorite
Sanitary
TEST OPERATION
10
MAX
max
Favorite
Sanitary
Favorite
Sanitary
Favorite
Sanitary
Connect the power plug to
the outlet.
In case of Coloreds program.
Connect the inlet hose.
Preparation for
Press the POWER button.
Press the Start/Pause
washing.
button.
·Press the Temp. button
·Check if the drum rotates
·Check if water is supplied
and the present temperature will
clockwise and counterclockwise.
through the detergent dispenser.
be displayed.
·Power off and then power on.
·Check if the door can be
·Check if the door can be
opened after 3 minutes.
·Turn off Wash and Rinse after
pressing the Start/Pause button
and start the machine again.
and start the machine again.
·Check drain and spin.
·If SVC is needed during
check, remove
the remaining water by pulling
out the hose cap.
Check the water heating.
Check automatic reverse
Check the water supply.
turn.
Check drain and spin
Power off and open the
Water removal
door
Click on the first or last page to see other WD-R1028UDS service manuals if exist.