LG WD-8054FB Service Manual ▷ View online
①
① Remove the back cover.
②
②
② Take off the belt turning the pulley.
③
③
③ Unscrew the bolt to pull out the pulley.
①
① Unscrew 2 screws from the bracket.
②
②
② Push the motor in the arrow direction for
disassembling.
③
③ When reassembling the motor, make sure that motor
mounting rubbers are not taken off from the bracket.
①
① Pull out the hinge pressing its snap.
②
②
② Do not use the pulled out hinge again. It may be taken
off during operation.
1
2
3
Hinge,
Damper
Damper
Damper
PULLEY, MOTOR, DAMPER
(PULLEY)
(MOTOR)
(DAMPER)
Open the lower cover cap (
)
by using coin.
Unplug the drain plug (
) , then
the water flows out,
At this time use a vessel
to prevent water flowing on the
floor. If the water does not flow any
more,turn the pump filter (
At this time use a vessel
to prevent water flowing on the
floor. If the water does not flow any
more,turn the pump filter (
)
open to the left.
Take out any foreign material
from the pump filter (
from the pump filter (
). After
cleaning, turn the pump filter(
)
clockwise and insert the
drain plug (
drain plug (
)to the original
place. close the lower cover cap.
Clean the drain pump filter
1
100
3
2
3
2
■ WD-1054(6)F(H)(B) / WD-1254(6)F(H)B / WD-8054F(H)B
40
Cap
(Remaining Hose)
Screw
Pump Outlet Hose
Tub Pump Bellows
41
①
① Remove pump outlet hose.
②
②
② Remove tub pump bellows.
③
③
③ Remove cap (Remaining Hose.)
④
④
④ Disconnect the wiring.
⑤
⑤
⑤ Unscrew 3 screws
⑥
⑥
⑥ Remove the pump.
①
① Unscrew 3 screws fixing the heater protecting cover.
②
②
② Loosen the M6 heater nut to pull out the heater.
①
① Loosen the M6 heater nuts to pull out the HEATER
ASSEMBLY.
When mounting the HEATER ASSMBLY be sure to
insert the HEART ASSEMBLY into the heater clip on
the bottom of the tub.
①
① Pull it out by holding the thermistor bracket.
If it is pulled by the wire, it may be broken.
②
② When mounting the thermistor again, make sure that it
is got back tight to the rubber.
PUMP
HEATER
THERMISTOR
CAUTION
■ WD-1054(6)F(H)(B) / WD-1254(6)F(H)B / WD-8054F(H)B
■ WD-1054(6)F(H)(B) / WD-1254(6)F(H)B / WD-8054F(H)B
42
DOOR HINGE ASSEMBLY
SWITCH ASSEMBLY, DOOR LOCK
WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB
①
① Disassemble the door from the door hinge.
②
②
② Take apart the cabinet cover clamp and release the
gasket.
③
③ Unscrew 2 screws on the door hinge.
④
④
④ Press the door hinge arm to the inside of the cabinet
cover for disassembling.
①
① Take apart the cabinet cover clamp and release the
gasket.
②
② Unscrew 2 screws holding the door lock.
③
③
③ Disconnect the door lock from the wiring connector.
①
① Remove the heater.
②
②
② Remove the foreign material (wire, coin and others) by
inserting a long bar through the hole.
11-1 THE EXPLODED VIEW OF CABINET ASSEMBLY
43
11 EXPLODED VIEW
A110
A101
A100
A430
A104
A102
A410
A200
A201
A220
A310
A300
A303
A133
A440
A140
A130
A131
A141
A450
A460
A273
A274
A274
A271
A272
A270
HOT(ORANGE)
COLD(BLUE)
HOT(ORANGE)
COLD(BLUE)
A275
A276
A277
HOT(ORANGE)
COLD(BLUE)
WD-6550F(B) / WD-8050F(H)(B) / WD-1050(5)F(H)(B)/WD-1253(5)F(H)(B)
A150
A154
A152
A153
A151
A134
Click on the first or last page to see other WD-8054FB service manuals if exist.