LG WD-80484NP Service Manual ▷ View online
8
HOW TO CONNECT INLET HOSE
Check that the rubber washer is the inside of the
valve connector.
Connect inlet hose firmly to prevent leak.
CONNECT DRAIN HOSE
CONNECT POWER PLUG
Make sure that the hose is not twisted.
The drain hose should be placed under 100cm from the floor.
Connect the power plug to the wall outlet.
Avoid connecting several electric devices,
It may be the cause of a fire.
Avoid submerging the end of the hose.
9
TEST OPERATION
Connect the power plug to
In case of cotton program.
the outlet.
Connect the inlet hose.
Preparation for
Press the power button.
Press the START/PAUSE
washing.
button.
Power off and then power on.
Check if the door can be
opened after 2 minutes.
Check if the door can be
opened after 2 minutes.
Press the Start/Pause button
after selecting Pump button by
pressing Program button.
after selecting Pump button by
pressing Program button.
If SVC is needed during
check, remove
the remaining water by pulling
out the hose cap.
Check the water heating.
Check automatic reverse
Check the water supply.
turn.
Check drain and spin
Power off and open the
Water removal
door
Check if the drum rotates
Check if water is supplied
clockwise and counterclockwise.
through the detergent dispenser.
10
5. OPE R ATION
W ater temper atur e
selector
selector
P ress the button to select
water temperature.
T he water temperature
water temperature.
T he water temperature
[60 C
95 C
C old
40 C ] can be
selected in C otton.
95 C is selected for C otton
and B aby C are.
and B aby C are.
O ption
R ins e+
Used to additional rinse, which may
assist in removing traces of detergent
residue.
assist in removing traces of detergent
residue.
B y selecting R inse+ function, the rinse
time and the rinse water are increased.
P re Was h
If the laundry is heavily soiled, "P re
Wash" course is effective.
P re Wash is available in C otton and
S ynthetic P rogram.
Wash" course is effective.
P re Wash is available in C otton and
S ynthetic P rogram.
L E D display
Display the program
procedure(Wash, R inse,
S pin, C hild Lock).
S pin, C hild Lock).
S ee troubleshooting guide.
C hild - lock
NOT E
If the P rogram lamps are blinked at the same time after the
power off or the end of the washing, the child lock mode is set.
C ancel the child lock mode by pressing the [Temp.] and the [ Option]
button simultaneously for 3 seconds.
power off or the end of the washing, the child lock mode is set.
C ancel the child lock mode by pressing the [Temp.] and the [ Option]
button simultaneously for 3 seconds.
C hild Lock system can be set and canceled by pressing both
[Temp.] and [Option] button simultaneously for 3 seconds.
Once C hild Lock is set, all buttons are not functioning except
power button.
C hild Lock system can be set anytime even during P ower-off
and operation.
It is automatically cancelled when an operational error occurs.
[Temp.] and [Option] button simultaneously for 3 seconds.
Once C hild Lock is set, all buttons are not functioning except
power button.
C hild Lock system can be set anytime even during P ower-off
and operation.
It is automatically cancelled when an operational error occurs.
In case of abnormal
operation, error indications
are displayed.
operation, error indications
are displayed.
11
S tar t/ P ause button
Use the button to start or pause
wash cycle.
T he power turn off automatically
4 minutes after the pause button
is pressed.
wash cycle.
T he power turn off automatically
4 minutes after the pause button
is pressed.
S pin
F 1066LP
R inse Hold
No S pin
400
1000
F 8066LP
R inse Hold
No S pin
400
800
O ption
Wash pr ogram selector
8 programs can be set depending on the type of the laundry.
B y turing the dial
B y turing the dial
[C otton
B aby C are
S ynthetic
Delicate
Hand Wash/Wool
Quick 30
R inse+S pin
S pin]
can be selected.
P ower button
P ress the button to turn
on and off.
on and off.
C reas e C are
If you want to prevent crease,
select this button with spin speed.
select this button with spin speed.
B io
If you want to eliminate protein
stains(milk, blood, chocolate...),
you may select B io by pressing the
option button.[Y ou can select B io
when temperature is higher than
60℃ in C otton, S ynthetic and B aby
C are.]
you may select B io by pressing the
option button.[Y ou can select B io
when temperature is higher than
60℃ in C otton, S ynthetic and B aby
C are.]
Click on the first or last page to see other WD-80484NP service manuals if exist.