LG WD-8030FB / WD-8030W / WD-8030W1 / WD-8030WF Service Manual ▷ View online
44
① The back cover is removed.
② The belt is pulled off while turning over the pulley.
③ The bolt is unscrewed to the shaft and then
② The belt is pulled off while turning over the pulley.
③ The bolt is unscrewed to the shaft and then
the pulley pulled off.
① Two screws are unscrewed from the bracket (Motor).
② The motor is pushed to arrow direction and then
② The motor is pushed to arrow direction and then
it is disassembled.
(When mounting the bushing should be fit the
bracket holder <Motor>)
① Lay the washing machine.
② The hinge (Damper) at the tub is pulled off
② The hinge (Damper) at the tub is pulled off
pressing on the snaps at the sharp end.
③ The hinge at the base is pulled off.
1
2
3
Hinge,
Damper
Damper
Damper
PULLEY, MOTOR, DAMPER
(PULLEY)
(MOTOR)
(DAMPER)
45
Pump
Outlet Hose
Tub Pump Hose
① Remove the pump outlet hose.
② Remove the tub pump hose.
③ The pump connectors are disconnected, the hose is
② Remove the tub pump hose.
③ The pump connectors are disconnected, the hose is
pulled off.
④ Three screws are unscrewed.
⑤ The pump is disassembled to arrow direction.
⑤ The pump is disassembled to arrow direction.
① Three screws are unscrewed.
② The heater M6 bolt is loosened and it is
② The heater M6 bolt is loosened and it is
released through the tub cover.
When mounting the heater, the heater should be
inserted the heater clip on the bottom of the tub.
① Pull it out by holding the thermistor bracket.
If holding the wire and pulling out it, it may be broken.
The thermistor should be checked it is pulled
to the rubber tightly.
PUMP
HEATER
THERMISTOR
CAUTION
46
DOOR HINGE ASSEMBLY
SWITCH ASSEMBLY, DOOR LOCK
WHEN FOREIGN MATERIAL STACK BETWEEN DRUM AND TUB
① Two screw are unscrewed on the door and the
door is disassembled.
② The cabinet cover clamp is removed and the
gasket is released.
③ Two screws are unscrewed on the door hinge.
④ The door hinge is disassembled by pressing
④ The door hinge is disassembled by pressing
the door hinge arm inside the cabinet cover.
① The cabinet cover clamp is removed and
the gasket is released.
② Two screws are unscrewed.
③ The door lock S/W is disconnected from the
③ The door lock S/W is disconnected from the
wiring connector and the strap.
① The heater is removed.
② The foreign material (wire, coin, etc) is removed
② The foreign material (wire, coin, etc) is removed
by inserting the long bar in the hole.
47
11-1.THE EXPLODED VIEW OF CABINET ASSEMBLY
11. EXPLODED VIEW
A110
A101
A100
A430
A104
A102
A410
A200
A201
A220
A310
A300
A303
A133
A132
A140
A130
A131
A141
A450
A460
A150
: Non-service part
: Service part
A273
A274
A271
A272
A270
HOT(ORANGE)
COLD(BLUE)
HOT(ORANGE)
COLD(BLUE)
A275
A276
A277
HOT(ORANGE)
COLD(BLUE)
A440
A301
Click on the first or last page to see other WD-8030FB / WD-8030W / WD-8030W1 / WD-8030WF service manuals if exist.