LG WD-21600 Service Manual ▷ View online
53
2 Push out PANEL ASSEMBLY, CONTROL after
Push the hook( , ) below.
1 The plate assembly(Top) is disassembled.
2 Pull out the drawer and unscrew 2 screws.
1 Unscrew two screws.
3 Unscrew the screws from the lower cover.
2 The cabinet cover clamp is removed by
special jig for service and the gasket is
released.
released.
3 Two screws are unscrewed.
4 Unscrew all the screws on the upper and
lower sides of the CABINET COVER.
1
2
3 Lift the side the Control Panel Assembly and
pull it out
CABINET COVER
54
1 Lift and separate the cabinet cover.
NOTE: When assembling the CABINET
COVER, connect the Door S/W connector.
COVER, connect the Door S/W connector.
• Just check cut-off.
• Check the operating time.
* Door Locking time :
1~8
sec.
Check the time between from
input the power to parts
move up, then Door locked.
input the power to parts
move up, then Door locked.
* Door Releasing time :
25~100
sec.
Check the time between from off
the power to parts
move down, then Door released.
the power to parts
move down, then Door released.
1
1
1
1 Unscrew two screws and cabinet cover
disassembled.
2 The Door Lock S/W is disconnected from the
wiring connector and the strap.
SWITCH ASSY, DOOR LOCK
55
• V ~ U (8~11Ω)
• U ~ W (8~11Ω)
• W ~ V (8~11Ω)
• U ~ W (8~11Ω)
• W ~ V (8~11Ω)
Motor Stator
U V W
Hall Sensor
Ha
Hb
Common
• Common ~ Ha (5~15kΩ)
• Common ~ Hb (5~15kΩ)
• Common ~ Hb (5~15kΩ)
1 Remove the housing coupled the TSG
(Connector, Hoses, Earth Screw)
[F1
❋03FDS]
2 Take out the screw of the TSG.
1 Remove the back cover.
2 After loosening the bolt, Rotor, pull out the
rotor.
1 Remove the 6 bolts from the stator.
2 Disconnect the 2 connectors.
2 Disconnect the 2 connectors.
1 Remove the hinges (Damper) at the Tub.
3 The hinge at the base is pulled off.
(In directions of the arrow)
2 The Hinge(Damper) at the base is pulled off by
pressing on the snaps at the sharp end.
TSG (TURBO STEAM GENERATOR)
ROTOR ASSEMBLY, STATOR ASSEMBLY, FRICTION DAMPER
< Heater for STEAM>
• Rating : 230V 1000W
• Resistant : 42.5~49.5Ω
• Rating : 230V 1000W
• Resistant : 42.5~49.5Ω
56
1 Remove pump outlet hose.
2 Remove tub pump bellows.
2 Remove tub pump bellows.
1 Loosen the nut.
2 Remove washing heater by pulling out.
2 Remove washing heater by pulling out.
When assembling the washing heater, insert
the heater to heater clip on the bottom of tub
and check the position of wire color.
the heater to heater clip on the bottom of tub
and check the position of wire color.
3 Remove cap(Remaining Hose).
4 Disconnect the wiring.
5 Three screws are unscrewed from the cabinet.
5 Three screws are unscrewed from the cabinet.
6 Remove the pump to arrow direction.
PUMP
HEATER
• Rating : 220/240V 50Hz
• Resistant : 162~176Ω
• Resistant : 162~176Ω
< Heater for Washing>
• Rating : 230V 2000W
• Resistant : 24.5~28.5Ω
• Rating : 230V 2000W
• Resistant : 24.5~28.5Ω
CAUTION
Click on the first or last page to see other WD-21600 service manuals if exist.