DOWNLOAD LG WD-1403AD5 / WD-1484ADP Service Manual ↓ Size: 18.53 MB | Pages: 50 in PDF or view online for FREE

Check the horizontality with a level (Gage).

8

If washing machine legs are loose or not screwed, then 

with the spanner wrench. 

Using the level, level the washing machine from front to back and side to side.

Using the spanner wrench to adjust leg for 

and try for 

.

Perform a Rinse and Spin with some clothing in the machine.

To do this, put 2~3kg of clothing in the unit, power on the unit, press the Rinse and Spin 
button, and then start. When the unit reaches the spin cycle, watch for vibrations.
If the unit is vibrating, make small adjustments to the leg until they subside. (Try 2Step again)

the lock nut against the base of the machine to 

the 

.

Lower the foot until there is no gap between floor and foot.
And only use 

when difference at the leg adjustment is more than 

.

Place your right hand on the back, right corner and your left hand on the front,
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right side and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.

If the unit is level, it will not rock.  However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot under the hand that is on the front of the machine.

A level

Higher

Tighten

Adjustable feet

Tighten

Adjustable feet

Higher

Tighten

Adjustable feet

Lower

Lock nut

10mm

Adjustable bolt

Tighen the lock nut

4620ER3001B
(Gray)

for Wooden floors

Rubber Cup

4620ER3001A
(Black)

for Tile floors

Test operation

9

Preparation
for 
washing.

· Connect the power plug to the

outlet.

· Connect the inlet hose.   

Press the power button.

Press the START/PAUSE
button.

Check the water heating.

· Press the Option(Left) + Temp.

button simultaneously and the
present temperature will be
displayed. 

Page 13

· Check if the drum rotates

clockwise and  counterclockwise. 

Check automatic reverse turn.

Check the water supply.

· Check if water is supplied through

the detergent dispenser.

Check drain and spin.

· Turn off Wash and Rinse after

pressing the Start/Pause button
and start the machine again.

· Check drain and spin.

· Power off and then power on.
· Check if the door can be

opened after 3 minutes.

Power off and open the
door.

Water removal.

· If SVC is needed during  check,

remove the remaining water by
pulling out the hose cap.

· In case of Coloreds program.

5. OPERATION

• Rotate the Cycle selector

knob to select the cycle
designed for different
types of fabric and soil
levels.

• Use this button to turn the

power On/Off.

• Use this button to Start/

Stop the washer.

• Pre Wash : If the laundry is heavily soiled, “Pre Wash” Cotton is

recommended.

• Rinse+ : Used to additional rinse, which may assist in removing

traces of detergent residue.

• Normal+Hold : If you desire to leave fabrics in the machine without

spinning after rinse to prevent wrinkling, you may select Normal+Hold
by pressing the Option button.

• Rinse + Spin : Use this option to rinse and then spin.

• Time Delay : Allows the start of any cycle to be

delayed for 3~19 hours.

• Favorite : Favorite program allows you to store a

customized operation for next use.

• Intensive : If the laundry is heavily soiled “Intensive”

option is effective.

• Medic Rinse : For high effectiveness or more purity in

rinse operation you can choose Medic Rinse option.
Medic Rinse is default in Baby Care program.

• The Beep on/off function can be set by pressing

and holding the Option and Spin button
simultaneouly.

• Use this option to prevent unwanted

use of the washer. Press and hold
Option(Left) and Spin button for 3
seconds to lock/unlock control.  

• When Child lock is set, CHILD LOCK

lights and all buttons are disabled
except the Power      button. You can
lock the washer while it is operating.

• Dry programs selected by rotating

dry knob.

• [Lower Temp. - Iron Dry - Cupboard

Dry - Eco Dry - Time(30,60,120)]
can be selected.

• Tub Clean course can be set by

pressing and holding Intensive and
Pre Wash button simultaneously. 

• Tub Clean is special cycle to clean

the inside of the washer.

• To change the spin speed,

Press the Spin button to cycle
through available options.

• Select a water termperature

based on the type of load you
are washing.